American Dryer Corp ADG-60 service manual To Remove or Replace Belt

Page 12

7. Reverse procedure for reinstalling power to the dryer.

IMPORTANT: When reinstalling the sensor bracket assembly to the dryer, be sure the internal wires do not get pinched between the sensor bracket and the holder.

8. Reestablish power to the dryer.

H. To Remove or Replace Belt

1.Discontinue power to the dryer.

2.Remove the lint drawer and the control and lint door from dryer.

3.If top basket (tumbler) is being serviced, remove control box assembly and belt guard from idler arm. Follow control box remove procedure in sections A and B.

4.Remove panel from basket (tumbler) being serviced. Follow from panel removal procedure in section E.

5.Loosen the tension on the idler arm adjusting spring by loosening the two (2) 9/16" nuts on the spade bolt.

6.Remove the motor pulley from the shaft. This can be done by rolling the fan belt off the pulley. Then loosen the set screw of the motor pulley and slide the pulley off the shaft.

7.Slide belt off the idler bracket and motor shaft.

8.Push belt up into basket (tumbler) area through the brushes and opening in the wrapper.

9.Remove the belt by maneuvering it back and forth and sliding it forward with your hands up through the lint drawer area.

10.The belt will come out from the front of the dryer between the basket (tumbler) and the wrapper.

11.Reverse procedure for installing new belt.

IMPORTANT: Be sure to set proper belt tension at idler adjustment. Follow belt and idler tension adjust- ment procedure in section K.

12. Reestablish power to the dryer.

8

Image 12

Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo remove gas valve train assembly To Remove Lint DrawerTo remove control middle or lint lower door To Remove and Replace Lint Drawer Switch Assembly To Remove Control BoxTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Sail Switch To Replace Main Door SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultFF. To Install New Main Door Glass EE. To Remove Main DoorGG. To Replace Main Door Gasket HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50