American Dryer Corp ADG-60 service manual Loctite

Page 16

LOCTITE ®

LOCTITE® is being used on ALL small dryers (AD-15 through AD-81 including stack dryers) that are manu- factured by ADC. LOCTITE® is being applied to ALL bearing set screws, used on ALL basket (tumbler) shafts, ALL idler shafts, ALL impellor (fan and blower) shafts, and ALL drive shaft bearings.

IMPORTANT

LOCTITE® ADHESIVE HAS BEEN USED

TO SECURE SET SCREWS AND BEARINGS

IN PLACE, ONCE SET SCREWS HAVE BEEN

REMOVED, A GEAR PULLER MAY BE NECESSARY

TO REMOVE BEARING TO AVOID DAMAGE.

P/N 112801

One (1) of these labels is attached to each Basket (tumbler) Bearing Assembly (pillow block bearing box). On the ADG-630 dryer this label is affixed near the small Impellor (fan) Shaft Bearing.

Should readjustments or removal of set screws become necessary in the field and the process becomes difficult, apply heat to the set screw with a soldering gun (450º F) for a few minutes.

IMPORTANT: Readjustment and removal of the Impellor (fan) Shaft bearings using Green LOCTITE® (#609) require that the bearing itself be heated.

In lieu of heating, ADC recommends the replacement of these assemblies in order to provide a true fit and avoid any warpage upon reinstallation.

NOTE: The application of LOCTITE® during the dryer manufacturing process does not preclude the recommended six (6) month interval that ADC advises for periodically checking ALL set screws within the dryer.

12

Image 16

Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultFF. To Install New Main Door Glass EE. To Remove Main DoorGG. To Replace Main Door Gasket HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50