American Dryer Corp ADG-60 DD. To Replace Coin Vault, Discontinue power to the dryer

Page 30

3.Remove the lint drawer, the control and lint door, and the gas valve train assembly from the dryer. Follow gas valve train removal procedure in section C.

4.With the gas valve train assembly removed from the dryer, remove the two (2) sets of nuts securing the manifold bracket to the gas valve train slide.

5.Pull manifold and valve assembly back slightly so that the burner orifice is exposed.

6.Unscrew burner orifice and replace with L.P. orifice.

IMPORTANT: Use extreme care when removing and replacing orifice. This orifice is made of brass and is easily damaged.

NOTE: Consult factory when replacing orifice for elevations over 2,000 feet.

7.Reinstall the valve and manifold assembly by reversing steps 4 through 6.

8.Locate valve regulator adjustment cover. Remove cover with slotted screwdriver, install valve L.P. stem and spring kit, then reinstall cover.

9.Reinstall the gas valve train assembly removed in step 3.

IMPORTANT: Use extreme care when removing and replacing the orifice. This orifice is made of brass and is easily damaged.

10.Reinstall the control and lint door and the lint drawer removed in step 3.

11.Convert opposite basket by following steps 2 through 11.

12.Once the conversion of both baskets is complete, open all gas shut-off closed in step 2.

IMPORTANT: The gas valve pressure regulations are now blocked open. Gas pressure must now be regulated at the source (L.P. tank) or a regulator must be added in the gas supply line of each dryer. A consistent pressure of 10.5 to 11 inches must be provided.

13. Reestablish power to the dryer.

DD. To Replace Coin Vault

1.Discontinue power to the dryer.

2.Remove both (upper and lower) lint drawers and the control and lint doors from the dryer. Follow lint drawer, and control and lint doors from the dryer. Follow lint and control and lint removal procedures in sections A and B.

3.Remove the control box and the lower front panel from the dryer. Follow front panel removal procedures in section E.

4.Remove the coin box.

5.From inside of coin vault, loosen and remove the four (4) nuts securing the coin vault to the dryer inner top, then the coin vault from the dryer.

6.Install the new coin vault by reversing step 5. Do not tighten the four (4) nuts. They must be left lose at this time for the coin vault adjustment.

7.Reinstall the front panel removed in step 3.

8.Tighten the four (4) coin vault HEX nuts left loosen in step 6.

9.Reinstall the coin box removed in step 4.

10.Reinstall the control box removed in step 3.

11.Reinstall control and lint doors, and lint drawers removed in step 2.

26

Page 29 Page 31
Image 30
Page 29 Page 31
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo remove gas valve train assembly To Remove Lint DrawerTo remove control middle or lint lower door To Remove and Replace Lint Drawer Switch Assembly To Remove Control BoxTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Sail Switch To Replace Main Door SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultGG. To Replace Main Door Gasket FF. To Install New Main Door GlassEE. To Remove Main Door HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50
Top Page Image Contents