American Dryer Corp ADG-60 service manual

Page 25

IMPORTANT: Readjustment and removal of the Impellor (fan) Shaft bearings using Green LOCTITE® (#609) require that the bearing itself be heated.

In lieu of heating, ADC recommends the replacement of these assemblies in order to provide a true fit and avoid any warpage upon reinstallation.

NOTE: The application of LOCTITE® during the dryer manufacturing process does not preclude the recommended six (6) month interval that ADC advises for periodically checking ALL set screws within the dryer.

1.Discontinue power to the dryer.

2.Remove the upper half of the rear split back guard panel to either the top or bottom basket (tumbler), depend- ing on which basket (tumbler) is being serviced.

3.Loosen pillow block bearing adjustment jam (hex) nuts and bolts (one [1] on each side of the bearing support).

4.Loosen the two (2) bearing set screws.

5.Remove the two (2) sets of nuts, washers and bolts securing the bearing to the bearing box support, then remove the bearing.

6.Reinstall bearing and hardware by reversing steps 3 and 5.

7.Make necessary vertical alignment and lateral alignment adjustments. Follow basket (tumbler) vertical align- ment and basket (tumbler) lateral alignment procedures in sections R and S.

IMPORTANT: Make sure proper belt adjustment is made.

8.Reinstall the upper half of the rear split back guard panel removed in step 2.

9.Reestablish power to the dryer.

21

Image 25

Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerEE. To Remove Main Door FF. To Install New Main Door GlassGG. To Replace Main Door Gasket HH. To Replace Main Door HingeNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50