American Dryer Corp ADG-60 service manual To Replace Sail Switch, To Replace Main Door Switch

Page 28

X. To Replace Sail Switch

NOTE: The sail switch and damper is located in the gas valve train assembly.

1.Discontinue power to the dryer.

2.Remove the lint drawer, and the control and lint door. Follow lint drawer, and control and lint door removal procedures in section II, A and B.

3.Remove sail switch and damper rod assembly from the dryer.

4.Disassemble sail switch bracket assembly from the dryer by removing the two (2) phillips head screws located in the lint drawer area.

5.Disassemble sail switch bracket assembly from the dryer by removing the two (2) slotted head machine screws securing the sail switch to the sail switch bracket.

NOTE: When disassembling the sail switch from the bracket, hold on to the twin speed nut located at the back side of the sail switch bracket into which the screws are threaded.

6.Disconnect the two (2) wires from the sail switch.

7.Reverse steps 3 through 6 for installing new sail switch.

8.Adjust the sail switch by bedning the actuator arm of the switch itself so that when the sail switch damper is manually closed the sail switch activates and when the damper is released the sail switch deactivates.

9.Reverse steps 1 and 2.

Y. To Replace Main Door Switch

1.Discontinue power to the dryer.

2.Open the main door completely.

3.Remove the two (2) phillips head screws holding the main door switch housing in place.

4.Disconnect the main door switch wires from switch, two (2) yellow wires.

5.Disassemble door switch by removing the two (2) nuts and washers holding the door switch in place.

6.Reverse this procedure for installing new door switch.

IMPORTANT: Under no circumstances should the door switch be disabled.

IMPORTANT: When reinstalling the door switch housing to the dryer, be sure the internal wires do not get pinched between the door switch housing and the front panel.

7. Reestablish power to the dryer.

Z. To Replace Direct Spark Ignition (DSI) Module

1.Remove the lint drawer, the control and lint door, and the gas valve train assembly from dryer. Follow gas valve train removal procedure in section C.

2.Disassemble DSI module and bracket assembly from the gas valve train slide by removing the two (2) sets of nuts and washers securing the bracket to the gas valve train.

3.Disconnect all wiring to the DSI module including the orange high voltage (HV) lead.

IMPORTANT: Identify location of each wire for correct reinstallation.

4.Disassemble DSI module from the bracket by removing the four (4) sets of nuts and washers securing the DSI module to the bracket.

5.Reverse steps 3 through 5 for installing the new DSI module.

24

Page 27 Page 29
Image 28
Page 27 Page 29
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultFF. To Install New Main Door Glass EE. To Remove Main DoorGG. To Replace Main Door Gasket HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50
Top Page Image Contents