American Dryer Corp ADG-60 service manual To Replace Basket tumbler Support Pillow Block Bearing

Page 24

7.Loosen the two (2) set screws on the pillow block bearing and flange bearing. The two (2) set screws on the flange bearing can be reached through the opening at the bottom of the bearing box.

8.Remove the basket (tumbler) and support assembly from the front of the dryer. If the basket (tumbler) cannot be removed freely, clean shaft area (with emery cloth) and spray with WD-40 or a similar lubricant. Then, with a block of wood against the shaft end, strike the block of wood with a hammer or mallet to move shaft past any burs made by the set screw.

IMPORTANT: Never strike the shaft directly with a hammer.

9.If entire basket (tumbler) and support assembly is being replaced proceed to step 11.

10.Removal of support from the basket (tumbler).

A.Remove the socket set screw at center of inside basket (tumbler) back wall.

B.Loosen and remove the three (3) sets of nuts and washers from the basket (tumbler) tie rods, then remove the three (3) tie rods.

C.Reassemble support to basket (tumbler) reversing the procedure.

11.Reassemble the basket (tumbler) and support assembly into the dryer by reversing steps 7 and 8.

12.Reinstall belt removed in step 5.

13.Reinstall the front panel removed in step 4.

14.Make the necessary vertical alignment and lateral alignment adjustments. Follow basket (tumbler) vertical alignment and basket (tumbler) lateral alignment procedures in section R and S.

15.Reinstall both (upper and lower) halves of the rear split back guard panels removed in step 6.

16.Make the necessary belt and idler adjustment. Follow belt and idler tension adjustment in section M.

17.Reverse steps 1 through 3.

U. To Replace Basket (tumbler) Support Pillow Block Bearing

LOCTITE ®

LOCTITE® is being used on ALL small dryers (AD-15 through AD-81 including stack dryers) that are manu- factured by ADC. LOCTITE® is being applied to ALL bearing set screws, used on ALL basket (tumbler) shafts, ALL idler shafts, ALL impellor (fan and blower) shafts, and ALL drive shaft bearings.

IMPORTANT

LOCTITE® ADHESIVE HAS BEEN USED

TO SECURE SET SCREWS AND BEARINGS

IN PLACE, ONCE SET SCREWS HAVE BEEN

REMOVED, A GEAR PULLER MAY BE NECESSARY

TO REMOVE BEARING TO AVOID DAMAGE.

P/N 112801

One (1) of these labels is attached to each basket (tumbler) bearing assembly (pillow block bearing box). On theADG-630 dryer this label is affixed near the small Impellor (fan) shaft bearing.

Should readjustments or removal of set screws become necessary in the field and the process becomes difficult, apply heat to the set screw with a soldering gun (450º F) for a few minutes.

20

Page 23 Page 25
Image 24
Page 23 Page 25
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo remove gas valve train assembly To Remove Lint DrawerTo remove control middle or lint lower door To Remove and Replace Lint Drawer Switch Assembly To Remove Control BoxTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Sail Switch To Replace Main Door SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultFF. To Install New Main Door Glass EE. To Remove Main DoorGG. To Replace Main Door Gasket HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50
Top Page Image Contents