American Dryer Corp ADG-60 Phase 5 System Diagnostics, Diagnostic L.E.D. Display Failure Codes

Page 47

SECTION VI

PHASE 5 SYSTEM DIAGNOSTICS

All major circuits, including door, lint door, lint drawer, microprocessor temperature sensor, heat and motor circuits are monitored. The Phase 5 Dual Microprocessor Controller (DMC) computer will inform the user, via the L.E.D. display and at the outputs of each relay (and door switch circuit) to easily identify failures.

A. Diagnostic (L.E.D. Display) Failure Codes

1."dOOr" - indicates door or lint drawer switch circuit is open.

a.Keyboard entry was made while main door is open or

b.There is a fault in the door switch circuit (external of the Phase 5 DMC (computer).

2."dSFL" - indicates a fault in the microprocessor temperature sensor circuit.

a.If a fault is detected in the microprocessor heat sensor circuit, the L.E.D. display will read "dSFL" and the buzzer (tone) will sound for approximately 5 seconds every 30 seconds until

1)power is corrected or

2)power to dryer is discontinued and the problem is then corrected.

IMPORTANT: The Phase 5 DMC (computer) has its own internal heat sensing circuit fuse protection located on the back side of the Phase 5 DMC (computer). If a "dSFL" condition occurs, check to see if this fuse has blown. If it has, do not replace the entire microprocessor controller (computer);

REPLACE ONLY THE FUSE and do so only with a 1/8-Amp (Slo Blo) fuse only.

NOTE: Once the Phase 5 DMC (computer) detects a problem in the heat circuit, it updates, every 30 seconds, so if the problem was a loose connection in this circuit which corrected itself, the "dSFL" condition would automatically be cancelled.

1."SEFL"

a.Indicates a rotational sensor circuit failure meaning that there is a fault somewhere in the basket (tumbler) rotation detection circuit or, the Phase 5 DMC (computer) program related to this circuit (PL01) is set incorrectly in the active mode (SEn) where the dryer is not equipped with the optional rotation sensor and should be set in the inactive mode (nSEn).

NOTE: If the dryer is equipped with the rotational sensor and the display reads "SEFL," reset by closing and opening the Program Switch (PS). Restart the dryer and if the "SEFL" code appears again, investigate further.

4."Hot"

a.Indicates a possible overheating condition. The Phase 5 DMC (computer) monitors the temperature in the dryer at all times. If the Phase 5 DMC (computer) detects that the temperature in the dryer has exceeded 170°F (77°C), it will disable ALL the outputs (shut the dryer down), the tone (buzzer) will sound for approximately 5 seconds and the display will read "Hot". The L.E.D. display will continue to read "Hot" until the temperature sensed has dropped to

43

Image 47
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo remove control middle or lint lower door To remove gas valve train assemblyTo Remove Lint Drawer To Remove Front Panel To Remove and Replace Lint Drawer Switch AssemblyTo Remove Control Box To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Direct Spark Ignition DSI Module To Replace Sail SwitchTo Replace Main Door Switch BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerHH. To Replace Main Door Hinge FF. To Install New Main Door GlassEE. To Remove Main Door GG. To Replace Main Door GasketNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50