American Dryer Corp ADG-60 To Replace either Motor Relay, Basket Tumbler Alignment Vertical

Page 20

3.Remove screw located in the bottom right hand corner of the control panel.

4.Disconnect the optic switch connector from the jumper connector. This is done by squeezing the optic switch connector tabs and pulling apart.

5.Remove the two (2) nuts holding the "U" shaped coin reject and return holder by using a 1/4" nut driver.

6.Remove the two (2) nuts located at the top of the coin acceptor with the same 1/4" nut driver. The coin acceptor can now be removed.

7.Reverse procedure for installing the new coin acceptor.

8.Reestablish power to the dryer.

Q. To Replace either Motor Relay

1.Discontinue power to the dryer.

2.Remove the lint drawer, and the control door from the dryer. Follow lint drawer, and control and lint door removal procedures in sections A and B.

3.Remove screw located in the bottom right hand corner of the control panel and open the panel.

4.Either relay can be removed with the control box in place on the dryer, or the control box can be removed from the dryer and placed on a flat surface. To remove the control box follow control box removal procedure in section D.

5.Disconnect the wires on the particular relay that needs to be replaced. Note the location of each wire on the relay.

6.Remove the motor relay from the control box by removing the two (2) screws and nuts securing it to the control box.

7.Replace new relay by reversing the steps above.

NOTE: Be sure to note the location of wires on the relay before removal.

R. Basket (Tumbler) Alignment - Vertical

1.Discontinue power to the dryer.

2.Remove the upper half of the rear split back guard panel to either the top or the bottom basket (tumbler), depending on which basket (tumbler) is being serviced.

3.Loosen the four (4) HEX head bolts in the sides of the bearing box (two [2] on each side).

4.Back off jam nuts on the two (2) Allen head adjustment screws.

5.Turn the screws clockwise evenly to raise the basket (tumbler) or counterclockwise evenly to the lower basket (tumbler).

6.Rotate the basket (tumbler) from the front and check alignment with the main door opening.

IMPORTANT: Leave larger gap from the inside ring on the top of the front panel opening to the basket (tumbler), and a smaller gap on the bottom to compensate for the weight of the clothes being dried.

7.Tighten the four (4) HEX head bolts on the sides of the bearing box, and the two (2) jams (hex) nuts on the Allen head adjustment screws.

16

Page 19 Page 21
Image 20
Page 19 Page 21
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo remove control middle or lint lower door To remove gas valve train assemblyTo Remove Lint Drawer To Remove Front Panel To Remove and Replace Lint Drawer Switch AssemblyTo Remove Control Box To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Direct Spark Ignition DSI Module To Replace Sail SwitchTo Replace Main Door Switch AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultFF. To Install New Main Door Glass EE. To Remove Main DoorGG. To Replace Main Door Gasket HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50
Top Page Image Contents