American Dryer Corp ADG-60 service manual Loctite

Page 13

LOCTITE ®

LOCTITE® is being used on ALL small dryers (AD-15 through 81 including stack dryers) that are manufactured by ADC. LOCTITE® is being applied to ALL bearing set screws, used on ALL basket (tumbler) shafts, ALL idler shafts, ALL impeller (fan and blower) shafts, and ALL drive shaft bearings.

IMPORTANT

LOCTITE® ADHESIVE HAS BEEN USED

TO SECURE SET SCREWS AND BEARINGS

IN PLACE, ONCE SET SCREWS HAVE BEEN

REMOVED, A GEAR PULLER MAY BE NECESSARY

TO REMOVE BEARING TO AVOID DAMAGE.

P/N 112801

One (1) of these labels is attached to each Basket (tumbler) Bearing Assembly (pillow block bearing box). On the ADG-630 dryer this label is affixed near the small Impeller (fan) Shaft Bearing.

Should readjustments or removal of set screws become necessary in the field and the process becomes difficult, apply heat to the set screw with a soldering gun (450º F) for a few minutes.

IMPORTANT: Readjustment and removal of the Impellor (fan) Shaft bearings using Green LOCTITE® (#609) require that the bearing itself be heated.

In lieu of heating, ADC recommends the replacement of these assemblies in order to provide a true fit and avoid any warpage upon reinstallation.

NOTE: The application of LOCTITE® during the dryer manufacturing process does not preclude the recommended six (6) month interval that ADC advises for periodically checking ALL set screws within the dryer.

9

Image 13

Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerEE. To Remove Main Door FF. To Install New Main Door GlassGG. To Replace Main Door Gasket HH. To Replace Main Door HingeNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50