American Dryer Corp ADG-60 service manual To Remove and Replace Sensor Bracket and Components

Page 11

4.To remove the lint drawer switch box assembly, remove the two (2) screws inside the lint drawer area that secure the box to the side of the lint coop.

5.Disassemble lint drawer box assembly from the dryer by disconnecting the two (2) harness connectors from the box assembly.

6.Remove the two (2) phillips head screws securing the cover to the switch mounting bracket.

7.Disassemble the switch from the box by removing the two (2) slotted head screws securing the switch to the bracket and disconnect the terminals from the switch.

8.Reverse procedure for reinstalling the lint drawer switch assembly.

9.Reestablish power to the dryer.

G. To Remove and Replace Sensor Bracket and Components

1.Discontinue power to the dryer.

2.Remove the lint drawer, and the control and lint door from the dryer. Follow lint drawer, and control and lint door removal procedures in sections A and B.

3.Pull the front of the sensor bracket forward to remove it from the "S" clips. Pivot bracket downward and assembly will separate from the sensor bracket holder.

4.To disassemble bracket assembly from dryer, disconnect the two (2) harness connectors.

5.To remove the temperature sensor and the connecting harness with its connectors:

A.Disassemble microprocessor sensor probe from the bracket by removing the 1/4" push-on fastener from the outside of the bracket.

B.Remove harness connectors by squeezing sides and pushing towards the center of the bracket.

C.Disconnect the two (2) wires from the 170º thermostat.

D.Reverse procedure for installing new sensor probe assembly.

6.To replace the 170º thermostat:

A.Remove the two (2) slotted head screws, washers, and nuts securing the 170º thermostat at the bracket assembly.

B.Reverse procedure for installing new 170º thermostat.

7

Image 11
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo remove control middle or lint lower door To remove gas valve train assemblyTo Remove Lint Drawer To Remove Front Panel To Remove and Replace Lint Drawer Switch AssemblyTo Remove Control Box To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Direct Spark Ignition DSI Module To Replace Sail SwitchTo Replace Main Door Switch BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerHH. To Replace Main Door Hinge FF. To Install New Main Door GlassEE. To Remove Main Door GG. To Replace Main Door GasketNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50