American Dryer Corp ADG-60 service manual DMC computer L.E.D. display reads Hot

Page 34

NOTE: Once the Dual Microprocessor Control (DMC) computer detects a problem, it updates every 30 seconds so that if a problem was a loose connection in this circuit which corrected itself, the "dSFL" display condition would automatically be cancelled.

a.Loose wire or termination in sensor harness somewhere between the sensor bracket and the Dual Microprocessor Control (DMC) computer.

b.Failed Dual Microprocessor Control (DMC) computer temperature sensor.

I. DMC computer L.E.D. display reads "Hot"

The "Hot" display condition indicates a possible overheating condition. The Dual Microprocessor Control (DMC) computer monitors the temperature in the dryer at all times. If the DMC computer detects that the temperature in the dryer has exceeded 170° F (77° C), it will disable ALL of the dryer outputs (shut the dryer down), the buzzer (tone) will sound for approximately 5 seconds, and the L.E.D. display will continue to read "Hot" until the temperature has dropped to 170° F (77° C) or lower and the DMC computer is manually reset by closing and opening the Program Switch (PS).

Possible reasons for overheating

1.Restriction in location exhaust duct work.

a.Dryer exhaust damper stuck in closed position.

b.Undersized exhaust duct work.

2.Insufficient makeup air.

J.DMC computer L.E.D. display reads "SEFL"

The "SEFL" display condition indicates a rotational sensor circuit failure which means there is a fault somewhere in the basket (tumbler) rotation detection circuit or the Dual Microprocessor Control (DMC) computer program related to this circuit (PL01) is set incorrectly in the active mode (SEn) with the optional rotation sensor and should be set in the nonactive mode ("nSEn").

If the dryer is equipped with the optional rotational sensor and for whatever reason the Dual Microprocessor Control (DMC) computer detects that the basket (tumbler) is not turning, it will disable ALL of the dryer outputs (shut the dryer down) and the L.E.D. will read "SEFL". The L.E.D. display will continue to read "SEFL" until the Dual Microprocessor Control (DMC) computer is manually reset by closing and opening the Program Switch (PS).

Possible causes

1.Loose or slipping (out of proper adjustment) basket or tumbler belt.

2.Broken basket or tumbler belt.

3.Failed motor.

4.Failure in the rotational sensor circuit

a.Failed rotational sensor.

b.Loose connection or break between the rotation sensor and the Dual Microprocessor Control (DMC) computer.

K.DMC computer will only accept certain keyboard (touchpad) entries

1.Failed Keyboard (touchpad) label assembly.

2.Failed Dual Control (DMC) computer.

30

Image 34
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultGG. To Replace Main Door Gasket FF. To Install New Main Door GlassEE. To Remove Main Door HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50