American Dryer Corp ADG-60 service manual Table of Contents

Page 5

Table of Contents
SECTION I
Routine Maintenance	3
A. Cleaning	3
B. Adjustments	4
C. Lubrication	4
SECTION II
Mechanical Section	5
A. To Remove Lint Drawer	5
B. To Remove Control (Middle) or Lint (Lower) Door	5
C. To Remove Gas Valve Train Assembly	5
D. To Remove Control Box	6
E. To Remove Front Panel	6
F. To Remove and Replace Lint Drawer Switch Assembly	6
G. To Remove and Replace Sensor Bracket and Components	7
H. To Remove or Replace Belt	8
I. To Remove or Replace Motor	10
J. To Remove or Replace Impellor (Fan)	13
K. Belt and Idler Tension Adjustment	13
L. Fan Belt and Tension Adjustment	14
M. To Remove Dual Control Microprocessor (DMC) Computer Panel Assembly	14
N. To Replace Dual Control Microprocessor (DMC) Computer	14
O. To Replace Touchpad (Keypad)	15
P. To Replace Coin Acceptor	15
Q. To Replace either Motor Relay	16
R. Basket (Tumbler) Alignment - Vertical	16
S. Basket (Tumbler) Alignment - Lateral	17
T. To Replace Basket (Tumbler) or Basket (Tumbler) Support	18
U. To Replace Basket (Tumbler) Support Pillow Block Bearing	20
V. To Replace Basket (Tumbler) Support Flange Bearing	22
W. To Replace 330º F (burner) Hi-Limit Switch (thermostat)	23
X. To Replace Sail Switch	24
Y. To Replace Main Door Switch	24
Z. To Replace Direct Spark Ignition (DSI) Module	24
AA. To Replace Ignitor and Probe	25
BB. To Replace Gas Valve	25
CC. To Convert Dryer from Natural Gas to Liquid Propane (L.P.) Gas	25
DD. To Replace Coin Vault	26
EE. To Remove Main Door	27
FF. To Install New Main Door Glass	27
GG. To Replace Main Door Gasket	27
HH. To Replace Main Door Hinge	27
SECTION III

Troubleshooting

28

Image 5

Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo remove control middle or lint lower door To remove gas valve train assemblyTo Remove Lint Drawer To Remove Front Panel To Remove and Replace Lint Drawer Switch AssemblyTo Remove Control Box To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Direct Spark Ignition DSI Module To Replace Sail SwitchTo Replace Main Door Switch BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerEE. To Remove Main Door FF. To Install New Main Door GlassGG. To Replace Main Door Gasket HH. To Replace Main Door HingeNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50