American Dryer Corp ADG-60 To Remove Lint Drawer, To remove control middle or lint lower door

Page 9

SECTION II

MECHANICAL SECTION

A. To Remove Lint Drawer

1.Pull out lint drawer three quarters of the way (approximately twenty inches).

2.Reach up into the back of the lint drawer and pull down the retainer (hinge) that is attached to the top of the lint drawer.

3.The lint drawer can now be removed.

4.Reverse procedure for reinstalling the lint drawer.

B. To remove control (middle) or lint (lower) door

1.Pull out lint drawer three quarters of the way (approximately twenty (20) inches). Reach into the back of the lint drawer and push down the retainer (hinge) that is attached to the top of the lint drawer.

2.Pull out the lint drawer.

3.Open the control and lint door (2) 1/4 turn locks, one (1) on each side.

4.Remove the control and lint door.

5.Reverse procedure for reinstalling the control and lint door.

C. To remove gas valve train assembly

1.Discontinue power to the dryer.

2.Close all gas shut-off valves in the gas supply line to the dryer.

3.Remove the lint drawer and the control and lint door from the dryer. Follow lint drawer and control and lint door removal procedures in section A and B.

4.Close the union shut-off valve at inlet area of the gas valve.

5.Loosen the union shut-off valve collar nut all the way.

6.Pull out gas valve train assembly 1/4 of the way. Disconnect the gas harness power connector at the top of the assembly.

7.Gently pull and remove the gas valve train assembly.

IMPORTANT: When removing the gas valve train assembly be careful not to snag or damage the gas valve train wiring disconnected in step 6.

8.Reverse procedure for reinstalling the gas valve train assembly.

NOTE: Be sure to open all gas shut-off valves closed prior to removing the gas valve train assembly.

9.Reestablish power to the dryer.

5

Image 9
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo remove gas valve train assembly To Remove Lint DrawerTo remove control middle or lint lower door To Remove and Replace Lint Drawer Switch Assembly To Remove Control BoxTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Sail Switch To Replace Main Door SwitchTo Replace Direct Spark Ignition DSI Module BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerEE. To Remove Main Door FF. To Install New Main Door GlassGG. To Replace Main Door Gasket HH. To Replace Main Door HingeNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50