American Dryer Corp ADG-60 service manual To Remove or Replace Motor

Page 14

I. To Remove or Replace Motor

1.Discontinue power to the dryer.

2.Remove the lint drawer and the control door from the dryer. Follow control and lint door removal procedures in sections A and B.

3.If top basket (tumbler) is being serviced, remove the control box from the dryer. Follow control box removal procedure in section D.

4.Remove the two (2) 9/16" (O.D.) nuts that are on the idler tension spade bolt.

5.Remove the motor pulley from the shaft. This can be done by rolling the fan belt off the pulley. Then loosen the set screw of the motor pulley and slide the pulley off the shaft.

6.Remove drive belt from motor shaft.

7.Remove the two (2) bolts, lock washers, and washers in front of the motor mount.

8.Remove the lower half of the rear split back guard panel to either the top or the bottom basket (tumbler), depending on which basket (tumbler) is being serviced.

9.Remove the four (4) 7/16" (O.D.) nuts which secure the impellor (fan) cover to the blower housing.

10.Remove the two (2) 7/16" (O.D.) nuts and lock washers which secure the impellor (fan) and shaft bearing to the impellor (fan) housing cover.

11.Loosen the two (2) set screws on the impellor (fan) and shaft bearing.

12.Remove the impellor (fan) and shaft bearing from the shaft. To do so, wedge a slotted screwdriver blade between the bearing and impellor (fan) cover and walk bearing back off shaft. The impellor (fan) cover will now separate from the blower (impellor and fan) housing.

13.Remove impellor (fan) lock nut (left hand) and lock washer securing impellor (fan) to fan shaft. This can be done by turning the lock nut to the left with an adjustable wrench, or more advisable, with a 1-1/8" deep socket ratchet wrench in an effort to avoid damaging the lock nut.

14.Align impellor (fan) to the center of the blower housing hole and remove impellor (fan) by grasping fan with both hands and pulling outward. The key will also come off the motor shaft in this procedure.

15.Return to the front of the dryer and disconnect the wiring harness from the motor.

16.Remove the motor through the front of the dryer take motor mount off motor (4 nuts, washers, lock wash- ers).

NOTE: When replacing the motor use P/N 881599. This will come with a keyed motor shaft and a new pulley to accommodate the keyed shaft.

17.Reconnect the wiring harness disconnected from the motor in step 15.

18.Insert key into the motor shaft removed in step 14, line up keyway in impellor (fan) with key in the shaft and slide impellor (fan) all the way onto shaft.

19.Reinstall the lock washer and lock nut (right hand) removed in step 13 and tighten securely.

20.Reassemble the impellor and shaft bearing to the impellor (fan) cover and secure (hand tighten only) with the two (2) nuts removed in step 10. Install the housing cover and bearing assembly onto the shaft and housing. Secure the two (2) set screws on the impellor (fan) and shaft bearing. Be sure that these set screws are securely in place.

10

Page 13 Page 15
Image 14
Page 13 Page 15
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo remove control middle or lint lower door To remove gas valve train assemblyTo Remove Lint Drawer To Remove Front Panel To Remove and Replace Lint Drawer Switch AssemblyTo Remove Control Box To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Direct Spark Ignition DSI Module To Replace Sail SwitchTo Replace Main Door Switch AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultGG. To Replace Main Door Gasket FF. To Install New Main Door GlassEE. To Remove Main Door HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50
Top Page Image Contents