American Dryer Corp ADG-60 service manual Basket Tumbler Alignment Lateral

Page 21

8.Check belt tension and make the necessary adjustments. Follow belt and idler tension adjustments procedure in section K.

9.Reinstall the upper half of the rear split back guard panel removed in step 2.

10.Reestablish power to the dryer.

S. Basket (Tumbler) Alignment - Lateral

1.Discontinue power to the dryer.

2.Remove the upper half of the rear split guard panel to either the top or the bottom basket (tumbler), depending on which basket (tumbler) is being serviced.

3.Loosen the two (2) HEX head bolts (one (1) turn is enough) that hold the pillow block bearing to the bearing box.

4.Back off the two (2) jam (HEX) nuts on the side adjustment bolts. Rotate the basket (tumbler) from the front of the dryer, checking the space between the basket (tumbler) and the front panel. Door opening should be equal on each side.

5.The lateral adjustment (see illustration on page 17):

A.To increase gap R, loosen (turn counterclockwise) adjustment bolt A and tighten (turn clockwise) adjustment bolt B.

B.To decrease gap R, loosen (turn counterclockwise) adjustment bolt A and tighten (turn clockwise) adjustment bolt B.

C.To increase gap L, loosen (turn counterclockwise) adjustment bolt A and tighten (turn clockwise) adjustment bolt B.

D. To decrease gap L, loosen (turn counterclockwise) adjustment bolt A and tighten (turn clockwise) adjustment bolt B.

6.Tighten and secure both adjustment bolts and jam.

7.Tighten bearing bolts loosened in step 3.

8.Check belt tension and make the necessary adjustments. Follow belt and idler tension adjustment procedure in section K.

9.Reinstall the upper half of the rear split back guard panel removed in step 2.

10. Reestablish power to the dryer.

17

Image 21

Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo remove gas valve train assembly To Remove Lint DrawerTo remove control middle or lint lower door To Remove and Replace Lint Drawer Switch Assembly To Remove Control BoxTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Sail Switch To Replace Main Door SwitchTo Replace Direct Spark Ignition DSI Module BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerEE. To Remove Main Door FF. To Install New Main Door GlassGG. To Replace Main Door Gasket HH. To Replace Main Door HingeNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50