DeWalt DP3700 Connect high-pressure hose C to pump outlet, Turn the water source on

Page 12

English

•DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty.

CAUTION: NEVER pull water supply hose to move pressure washer. This could damage hose and/or pump inlet.

•DO NOT use hot water, use cold water only.

•NEVER turn water supply off while pressure washer engine is running or damage to pump will result.

4.Verify the filter screen (V) is in water inlet of pump.

5. Connect the cold water source (X) to pump inlet.

NOTE: Water source must provide a minimum

 

of 5 gallons per minute at 20 PSI.

V

WARNING: To reduce the possibility of con-

 

tamination always protect against backflow when

 

connected to a potable water system.

 

• DO NOT stop spraying water for more than two

U

minutes at a time. Pump operates in bypass

 

mode when spray gun trigger is not pressed.

 

When the temperature inside the pump rises

 

too high the thermal relief valve (U) will open

 

and release a gush of water in an effort to lower

 

the temperature inside the pump. The thermal

relief valve will then close. If pump is left in bypass mode for more than two minutes internal components of the pump can

6.Connect high-pressure hose (C) to pump outlet.

7.If applying a chemical or cleaning solution, refer to Chemicals and Cleaning

Solvents.

8.Turn the water source on.

CAUTION: Risk of property damage. Failure to do so could cause damage to the pump.

C

X

be damaged.

START-UP PROCEDURE

1.In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure.

2.Check engine oil level. Refer to the engine instruction manual for correct procedure.

3.Connect the water hose to the water source. Turn the water source on to remove all air from the hose. When a steady stream of water is present, turn the water source off.

9.Remove all air from the pump and high pressure hose by depress- ing trigger until a steady stream of water is present.

10.Start engine. Refer to the engine instruction manual for correct procedure.

WARNING: Risk of unsafe operation. If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

11. Depress trigger on gun to start water flow.

WARNING: Risk of unsafe operation. Stand on a stable surface and grip gun/wand firmly with both hands. Expect the gun to kickback when triggered.

12. Release trigger to stop water flow.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DP3700 Engine Pump Specifications SpecificationsHandle assemble CAT 67DXDefinitions Safety Guidelines Important Safety InstructionsHOW to Prevent IT What can Happen HOW to Prevent ITWhat can Happen Some cleaning fluids Use only cleaning fluids When using replacementUse only accessories rated Eyes or lungs Follow manufacturersNever leave wand unattended while unit is running When Transporting or Storing To these very rapidly. Adjust Use a tire pressure gaugeTo check the tires pressure Before each use and while Installation Pressure Washer Assembly Fig For Future USE Pressure Adjustments OperationSpray Wand Nozzles Fig Chemicals and Cleaning Solvents StartingChanging Nozzles on Spray Wand To Apply Chemicals and SolventsSTART-UP Procedure Connect high-pressure hose C to pump outletTurn the water source on Maintenance HOW to Change Pump OILEngine Pump To Check OILTo Clean the Water Inlet Filter To Remove TiresStorage Accessories Service Information Pressure WasherRepairs Date and Place of PurchaseLimited Warranty Troubleshooting Guide GlossaryTroubleshooting Codes Code Possible Cause Possible SolutionTroubleshooting Codes Moteur Caractéristiques techniques de la pompeFiche technique Définitions lignes directrices en Matière de sécuritéDirectives de sécurité importantes Et des conditions de fonctionnement et d’autres variablesConserver CES Directives CE QUI Peut SE Produire Comment L’ÉVITERDu matériel déposé contre De l’équipement et proVoquer une surchauffe et ’incendieCE QUI Peut SE Produire SuiteFrançais Suivre la procédure de Démarrage correcte pourQui provoquerait ainsi une Au brasAvertissement Risque D’ÉCLATEMENT Avertissement Attention Surfaces ChaudesAvertissement Risque DE Brûlure Chimique Assemblage de la laveuse haute pression Fig Conserver CES Directives Pour UN Usage UltérieurAvertissement Risque Dechoc Électrique Avertissement Risque DE Blessure EN Soulevant LE ProduitFonctionnement Réglages de la pressionBuses du tube de pulvérisation Fig Produits chimiques et solvants de nettoyage Changement DES Buses SUR LE Tube DE PulvérisationApplication DE Produits Chimiques ET Solvants Démarrage Procédure DE Démarrage Enfoncer la détente du pistolet pour activer le jet d’eauRelâcher la détente pour arrêter le jet d’eau Entretien PompeVérification DU Niveau D’HUILE Méthode DE Vidange DE ’HUILE DE LA PompeNettoyage du filtre de l’admission d’eau Retrait des pneuRangement Glisser le collet hors de l’essieu et retirer le pneuAccessoires Laveuse haute pressionInformation SUR LES Réparations RéparationsGarantie limitée Date et lieu de l’achatGlossaire Code Cause Probable Solution Probable Guide de dépannageCodes de dépannage Le moteur ne démarre pas 3, 4, 5, 6, 7Codes de dépannage suite Que l’eau Motor Especificaciones de la bombaBomba de alta presión Motor Aceite Use DP70 Capacidad de aceite 319,4 ml 10,8 ozEspecificaciones Definiciones Normas de seguridadInstrucciones de seguridad importantes OperaciónConserve Estas Instrucciones Peligro Riesgo DE Explosión O Incendio¿QUÉ Puede SUCEDER? Cómo Evitarlo Peligro Riesgo Respiratorio Asfixia Altas como para penetrar Asegúrese de que laLa carne humana y animal Por ello podría ocasionarPeligro Riesgo DE Operación Insegura Peligro Riesgo DE Lesión POR PulverizaciónSi el motor no arranca Apriete el disparador de laDe arranque lentamente Entonces, hale de élAdvertencia Riesgo DE DE Estallido Advertencia Riesgo DE Superficies CalientesAdvertencia Riesgo DE Quemadura Química Instalación Ensamblado de la lavadora a presión FigConserve Estas Instrucciones Para Futuras Consultas Advertencia Riesgo DE Descarga EléctricaOperación Ajustes a la presiónBoquillas para la varilla pulverizadora Fig Productos químicos y solventes de limpieza Cambio DE LAS Boquillas DE LA Varilla PulverizadoraPara Aplicar Productos Químicos Y Solventes Puesta en marcha Procedimiento DE Puesta EN MarchaApagado Abra la fuente de aguaBomba MantenimientoLimpieza de las boquillas Para Controlar EL AceitePara limpiar el filtro de entrada de agua Para quitar los neumáticosAlmacenamiento Lavadora a presión AccesoriosInformación DE Mantenimiento ReparacionesPóliza de Garantía Garantía limitadaIdentificación DEL Producto ExcepcionesCULIACAN, SIN Glosario Productos químicos y solventes de limpiezaGuía de detección de problemas Códigos de detección de problemasCódigo Causa Posible Solución Posible Operación Códigos de detección de problemas continuar Español Ewalt Industrial Tool Co., 701 Joppa Road, Baltimore, MD DEC06 Form No. A20830 DP3700 Copyright 2007 D Ewalt
Top Page Image Contents