Generac 004614-1 owner manual Major Features and Dimensions

Page 23

Generac®

45 [.94"] [1.77"]

26

[1.02"]

63

[2.48"]

371 [14.61"]

421 [16.57"]

]

567 [22.32"]

OVER SCREWS

BATTERY CONNECTION

POSITIVE (+)

BATTERY CONNECTION

NEGATIVE (-)

3/8-16 UNC MOUNTING HOLES

[4 PLCS]

[11.38"]

CENTER OF GRAVITY

376.5

[14.82"]

HOUR METER

516.5

[20.33"]

929 [36.57"]

OVER SCREWS

99SPARK ARRESTOR [3.90"]

LIFTING EYE

ACCESS COVER

RADIATOR CAP

ACCESS COVER

37.6

5.42"]

291.5

[11.48"]

[6.61"]

OIL FILL

OIL DIPSTICK

TOP/START SWITCH

FUSE (14 AMP)

RE HEAT

IRCUIT BREAKER

MOTE CONNECTION KNOCKOUT

5

0"]

289.5[11.40"]

ELECTRICAL ACCESS

AC POWER HARNESS

[1/2" LIQUID-TIGHT CONDUIT]

.5

38

595.0 [23.43"]

604 [23.78"]

OVER SCREWS

Figure 1.2 –

Major

 

Major Features and Dimensions

Features and Dimensions — Drawing No. D2650

QUIETPACT™ 65D Recreational VehicleGenerator

Section 1 – General Information

Power Systems, Inc.

536.3

[21.12"]

EXHAUST OUTLET

2

[1.16"]

REAR SERVICE PANEL

FRONT SERVICE DOOR

0"]

-A

21

Image 23
Contents Power SYSTEMS, INC Introduction Authorized Service Dealer LocationPart II Installation Instructions General Hazards Electrical Hazards Quietpact 65D Generator IdentificationGenerator AC Connection System SafetySpecifications Generator ApplicabilityGenerator Fuel Consumption GAL/HREngine OIL Requirements Before Starting the Engine Generator Control PanelOptional Remote START/STOP Starting the Generator Protection Systems Stopping the Generator1 25-HOUR BREAK-IN Period Additional InformationOverspeed Shutdown Overvoltage ProtectionEffects of Moisture and Dirt Checking the Engine OIL LevelChanging the Engine OIL AND/OR OIL Filter Operation in High Grass or BrushSpark Arrestor Muffler Servicing the Engine AIR FilterBattery Maintenance Cleaning the GeneratorDrive Belt OUT-OF-SERVICE ProcedureCooling System Engine CoolantReturn to Service SYSTEM/COMPONENT Procedure Frequency Service SchedulePart General Hazards Electrical Hazards Generator Engine Operating Speed Purpose and Scope ManualStandards Booklets Equipment DescriptionMajor Features and Dimensions Suspended Mounting Location and SupportGenerator Location Generator SupportCompartment Construction Generator CompartmentsGenerator Restraint Acoustics Sound Insulating MaterialsTypical Noise Abatement Compartment Floor CutoutsGenerator Airflow Cooling and Ventilating AIRCooling AIR Inlet Openings Compensating for Restrictions Testing the InstallationDiesel Fuel System Generator Fuel Return Lines Generator Fuel Supply LinesMuffler and Spark Arrestor Exhaust System SafetyExhaust System Generator AC Connections Electrical ConnectionsElectrical Junction BOX Isolating Different Power Sources Power Supply CordGround Fault Circuit Interrupters Battery Cable Connections Battery InstallationBattery Cables Recommended BatteryBattery Compartment Optional AccessoriesInitial Start Post Installation TestsTesting Under Load Before Initial StartupInstallation Checklist Problem Cause Correction Troubleshooting GuideAppendix 2 Electrical Data Appendix 2 Electrical Data Appendix 2 Electrical Data Appendix 3 Exploded Views and Parts Lists QTY Description Base Frame Weldment 174 Appendix 3 Exploded Views and Parts Lists Cooling System Drawing No. D2360 1926 Exhaust Gasket Description QTY Start / Stop Switch Camshaft Assembly Complete Cylinder Block Cylinder Head Assembly Crankshaft Assembly Part NO. QTY Description Rocker ARM Shaft Injector Pump Assembly Fuel Filter Support Appendix 3 Exploded Views and Parts Lists HOUSING, Timing Gear 3114 Water Pump Assembly Appendix 4 Notes Appendix 4 Notes Parts Covered Federal and California Emissions Control Warranty StatementYour Warranty Rights and Obligations Manufacturers Warranty CoverageLimitations Obtaining Warranty ServiceObligations and Rights of the Manufacturer and Owner Generac Power SYSTEMS, INC