Briggs & Stratton 40204, 40229 Before Initial START-UP, System Control Panel, Battery Connection

Page 14

INSTALLATION

System Control Panel

Figure 11 depicts the Home Generator System control panel, located inside the generator housing. Below are brief descriptions of the controls used during installation. More information may be found in the Operator’s Manual.

Figure 11 — Home Generator System Control Panel

15 Amp Fuse

Service Tool

 

System Switch

Digital Display

 

Set Exercise

Circuit

Breaker

Switch

 

 

Manual Over-Ride

 

Switch

System Switch

This two-position switch is the most important control on the system and is used as follows:

•“AUTO” position is the normal operating position. If a utility power outage is sensed, the system will start the generator. When utility power is restored, lets the engine

The system is filled with synthetic oil (API SJ/CF 5W-30W). This allows for system operation in the widest range of temperature and climate conditions.

NOTICE

Any attempt to crank or start the engine before it has been properly serviced with the recommended oil will result in equipment failure.

•Refer to engine manual for oil fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

NOTE: The use of synthetic oil DOES NOT alter the required oil change intervals described in the engine operator’s manual.

Battery Connection

The Home Generator System is supplied with a 12 Volt DC, AGM type, 55 Amp-Hour, valve regulated battery. It is a sealed, lead-acid rechargeable battery. It is installed in the unit and the battery cables are connected at the factory. The unit’s 15 Amp fuse, which isolates the battery and prevents the unit from starting, has been removed for shipping. The battery will lose some charge charge prior to installation of the generator. If battery voltage is below 12 Volts, charge the battery.

stabilize internal temperatures, shuts off the generator, and waits for the next utility power outage.

•“OFF” position turns off running generator, prevents unit from starting and resets any detected faults.

15 Amp Fuse

Protects the Home Generator System DC control circuits. If the fuse has ‘blown’ (melted open) or was removed, the engine cannot crank or start. Replace the fuse using only an identical ATO 15A fuse. One spare fuse is supplied with the unit.

BEFORE INITIAL START-UP

Engine Oil

This engine is shipped from the factory filled with the recommended oil. Before starting the engine, check oil level and ensure that engine is serviced as described in the engine operator’s manual.

Oil Considerations

Your Home Generator System is equipped with an engine that has been pre-run at the factory.

IMPORTANT: If battery voltage is below 5 Volts, it may not take a charge and you will need a new battery.

Charging the Battery

If it is necessary to charge the battery, proceed as follows:

1.Set generator's system switch to OFF.

2.Remove 15 Amp fuse from control panel.

3.Disconnect negative battery cable to negative battery terminal (indicated by NEGATIVE, NEG, or (-).

NOTICE

Failure to disconnect negative battery cable will result in equipment failure.

•DO NOT attempt to jump start the battery.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

4.Charge battery with battery charger at 2 Amps until battery holds 12 Volts.

NOTE: DO NOT exceed 13.7 Volts charging.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 12000 Equipment Description Table of ContentsInstaller Responsibilities Customer ResponsibilitiesDo not dispose of battery in a fire Important Safety RulesHazard Symbols and Meanings Engine exhaust from this product containsSafety Rules Installing the 15A fuse could cause the engine to start Installation General Location Guidelines Fuel and Electrical Inlet DimensionsLifting the Generator NPTTo lift Insert Access DoorsTo Open an Access Door PortTo Close an Access Door Do not light a cigarette or smokeTemporary Manometer Installed 10ft 15ft 20ft 30ft 40ft 50ft 60ft 70ft 80ft 90ft 100ft Fuel ConsumptionFuel Pipe Sizing 10ft 15ft 20ft 30ft 40ftSystem Connections Wiring for the 2 Pole ConnectorWiring for the 10 Pole Connector Generator AC Connection System Fault Detection SystemTo install the remote LED panel Grounding the GeneratorSystem Control Panel Battery ConnectionBefore Initial START-UP Engine OilFuel System Selection Servicing the BatteryTo configure the fuel system for LP use Fuel Supply SystemInitial START-UP no Load Engine AdjustmentInstall 15 Amp fuse in control panel For a 15kW Home Generator SystemGovernor Automatic Operation Sequence Setting Exercise TimerInstallation Inspection Withdrawal Rate 32F 20F 10F 30F 40F Fuel Comparison ChartPhysical Properties Propane Natural Gas Descripción DEL Equipo Dimensiones de la Entrada para ElectricidadTabla DE Contenido Responsabilidades DEL ClienteExplosión AdvertenciaSímbolos de Peligro y Significados Gases TóxicosLos generadores producen un voltaje muy poderoso Instala el fusible se puede producir el arranque del motor PrecauciónAviso Inspección al Momento de la Entrega InstalaciónPrecauciones al Momento del Desempaque Contenido de la CajaPautas Generales para la Ubicación del Generador Dimensiones de la Entrada para Electricidad y CombustibleElevación del Generador Para cerrar una puerta de acceso Puertas de AccesoPara abrir una puerta de acceso Sistema DE Combustible Gaseoso Figura 21 Manómetro Instalado Transitoriamente Gas Natural Vapor de PL Dimensiones de la Cañería de CombustibleConsumo de Combustible Gas Natural peso específico =Toma de 10 polos Contactos de fallo Conexiones DE SistemaCableado para toma bipolar Interconexiones del Circuito de Control Sistema de Conexión de c.a. del GeneradorConexión a Tierra del Generador Sistema de Detección de FallasConexión de la Batería Antes DEL Arranque Inicial DEL MotorPanel de Control del Sistema Aceite de MotorSistema de Suministro de Combustible Para configurar el sistema de combustible para uso de LPSelección DEL Sistema DE Combustible Servicio la BateríaPara sistema de generador de doméstico de 15kW Arranque Inicial SIN CargaAjuste del Motor Quite el tapón de la entrada LP de la válvula en TDel Regulador Tornillo de AjusteTemporizador de enfriamiento del motor Configuración DEL Temporizador DE PrácticaInspección Posterior a LA Instalación Tasa de consumo 32F 20F 10F 30F 40F Cuadro de Comparación de CombustiblesPropiedades físicas Propano Gas natural Description DE Léquipement Responsabilités DE LinstallateurTable DES Matières Responsabilités DE LacheteurExplosion Symboles de Danger et MoyensAvertissement Manuel dUtilisationNE touchez PAS les fils dénudés ou les boîtiers Avis Installation Directives Générales Concernant lEmplacement Soulèvement de la GénératricePortes dAccès Pour ouvrir une porte d’accèsPour fermer une porte d’accès Manomètre Temporaire Installé Il faudrait inclure une sortie pour manomètreGas Naturel Vapeur PL Consommation de CombustibleGrosseur du Tuyau de Combustible Gaz Naturel densité = 0,65Branchement de la prise à dix pôles Connexions DE SystèmeBranchement de la prise à deux pôles Prise à dix pôles Contacts de défaillanceSystème de Détection des Pannes Interconnexions du Circuit de CommandeMise à la Masse de la Génératrice Neutre De PuissanceBranchement de la Batterie Tableau de Commande du SystèmeAvant LE Démarrage Initial DU Moteur Huile à MoteurEntretien de la Batterie Sélection DU Système DE CombustibleSystème dAlimentation en Combustible Pour la groupe électrogène résidentiel de 12kWRaccordez le conduit d’essence à l’entrée LP . Soupape en T Démarrage Initial Sans ChargePour la groupe électrogène résidentiel de 15kW Réglez l’interrupteur de système de la génératrice sur onRéglage du Moteur Réglage DE LA Minuterie DE Cycle Dexercice Vérification InstallationCapteur de Prise en Charge de la Tension de Service Minuterie de Refroidissement du MoteurRemarques Charte de Comparaison des Combustibles Propriétés physiques Propane Gaz naturel

40229, 40204, 40213, 40234, 40210 specifications

Briggs & Stratton is a recognized leader in the small engine market, catering to both homeowners and professionals with a wide range of reliable engines. The models 40210, 40234, 40213, 40204, and 40229 are notable entries in this lineup, each designed to deliver power, efficiency, and durability for various applications.

The Briggs & Stratton 40210 is often appreciated for its compact size and robust performance in lawn care equipment. It features a 140cc engine with an overhead valve design that enhances fuel efficiency and reduces emissions. This model supports easy starting with its dependable pull-start system and is well-suited for pushing mowers and other light-duty machines.

In contrast, the 40234 model stands out with its 190cc engine, which provides an excellent power-to-weight ratio. This engine is engineered to tackle medium-duty tasks, making it ideal for residential lawn trimming and garden maintenance. The 40234 incorporates advanced features like a ReadyStart technology that eliminates the need for priming, allowing for a hassle-free starting experience in various weather conditions.

The Briggs & Stratton 40213 shares similarities with the 40234 but enhances user interaction and maintenance with a more user-friendly design. It employs a 163cc engine that combines optimal power with low vibration, ensuring smooth operation. This model is particularly favored for its extended runtime, enabling users to complete their lawn care jobs without frequent interruptions.

For those seeking a slightly less powerful option, the 40204 is an excellent choice. Featuring a reliable 125cc engine, it is designed for lighter applications. This model is particularly notable for its lightweight build, making it highly maneuverable and easy to handle for novice users and homeowners alike.

Lastly, the 40229 offers a balance between power and practicality, housing an 11.5 gross torque engine rated for robust tasks. This engine is crafted with innovative technologies that promote fuel efficiency while minimizing noise output, making it a favorite among environmentally conscious users. It also integrates user-friendly features, such as an easy-access air filter, which simplifies maintenance.

Across these models, Briggs & Stratton ensures high-quality construction and usability, with features like dual air filtration systems and durable components that withstand rigorous use. Each engine encapsulates the brand's commitment to innovation, performance, and reliability, catering to the diverse needs of consumers in the landscaping and outdoor maintenance sectors. Whether for small residential tasks or larger projects, these engines are designed to empower users with the performance they need to get the job done efficiently.
Top Page Image Contents