Emerson 400518-01 Sync Input Connector J10, Function Pin Number Electrical Characteristics

Page 43

Safety Information	Product Overview

Installation

Diagnostics

Options and Accessories

Specification

Sync Input Connector (J10)

Sync Input signals are connected to the drive using the 9-pin Sync Input connector.

If interfacing the drive using field wiring, the optional standard terminal interface board (STI-SNCI) may be used.

1 2 3 4

5 6 7 8

Figure 31:	STI-SNCI Interface Board

		J10 Connector			Function
			Pin#		Function
			Pin#
			1		Encoder A
			2		Encoder A/
			3		Encoder B
			4		+ 5 Vdc
			5		Encoder B/
			6		Encoder Z
			7		Encoder Z/
			8		Logic Common
			9		NC

Figure 32:Analog Input Connector (J10) Functions

Function	Pin Number	Electrical Characteristics
Encoder In	1, 2, 3, 5, 6, 7	Differential line driver input (RS 422)

5 Vdc	4	+5 Vdc supply voltage

Ground	8	Logic Common

The Sync Input power meets EMC emissions and immunity for cables longer than 3 meters [10 ft], when using a shielded cable. When a remote encoder is user, cable length may be limited by encoder supply voltage drop, and should not exceed 200 ft [60 m].

Installation

31

Image 43

Contents Epsilon EP Drive Page Epsilon EP Drive Installation Manual Reference Materials Safety Precautions General warning Listed 51Y8 IND. CONT. EQ Underwriters Laboratories ListedDrive Overload Protection Vii CE Declaration of ConformityViii Table of Contents Index Diagnostics and TroubleshootingOptions and Accessories SpecificationsProduct Overview Epsilon EP DriveProduct Overview Achieving Low Impedance Connections Basic Installation GuidelinesInstallation Electromagnetic Compatibility EMCElectrostatic Discharge ESD Protection Wiring NotesEnvironmental Considerations Nema Enclosure Panel LayoutOutside Enclosure Cable to Enclosure ShieldingInside Enclosure Epsilon EP Schaffner Control Techniques Rating Mechanical InstallationAC Line Filter Installation Notes AC Line FiltersMechanical Drawing for Epsilon Base and Indexing Drives Mechanical Drawing for Epsilon Programming Drive Drive Model Dimension a Minimum Panel Width Inches mmSystem Grounding High Power ConnectionsAC Supplies not Requiring Transformers AC Power RequirementsEarth Grounded Delta Distribution Transformer, 240 Vac 3Ø AC Supplies Requiring TransformersTo Fusing Transformer Sizing Single Phase Power Supply ConnectionsDrive/Motor Combination Suggested KVA Rating LPN-RK-10SP Line Fusing and Wire SizeOperation on DC Input Supply AC Input Power ConnectionsExternal Shunt Resistor External Shunt Electrical InstallationShunt Resistor Kit Installation Shunt ControlNT and MG Motors Motor Power WiringEpsilon EP NT/MG Motor Power Wiring Diagram Front View XV Motor Power WiringVoltage Range Model Current Low Power ConnectionsDC Logic Power Supply Wiring Logic Power Supply SpecificationMotor Overtemp Wiring Motor Feedback Wiring J6Connection of Encoder Quadrature and Marker Signals Connection of Encoder Commutation Signals to the DriveXV 130 mm Motor XV 40-80 mm MotorEpsilon EP to NT or MG Motor Brake Wiring Diagram Motor Brake WiringXV 40mm-80mm Input/Output and Drive Enable WiringConnector J3 Functions O Connector J3 Functions STI-SNCOA Analog/Sync Output Connector J5Function Pin Numbers Electrical Characteristics Function Pin Number Electrical Characteristics Sync Input Connector J10Encoder Output Signal Wiring Analog Command WiringDrive J5 Connector ShellNs Minimum Pulse Mode Wiring, Differential InputsCCW Pulse Mode Wiring, Single Ended InputsMaster/Slave Encoder Connections Communication Cables CommunicationsPin Function Epsilon EP Serial Communication Connector DeviceNet Port Serial Communications SpecificationsModbus Communications Ethernet PortInstallation Display Indication Status Description Diagnostic DisplayDiagnostics and Troubleshooting Status CodesFault Codes Display Fault Action to Reset Bridge Disabled Flash Invalid Fault DescriptionsLow DC Bus Threshold High DC Bus ThresholdTravel Limit + Drive Faults Diagnostic Analog Output Test PointsChannel Analog/Sync Output Connector J5 Pin# Rebooting the Drive Viewing Active Drive FaultsResetting Faults Epsilon EP Drive Options Options and AccessoriesSTI-24IO STI-SNCOA STI-SNCI STI-ENC Options and Accessories Specifications Epsilon EP SpecificationsControl Outputs Pulse ModeEncoder Output Signal Control InputsEnvironmental Fault Detection CapabilityDrive Weights Cooling MethodDrive Model Dimension a Dimension B Shown in inches/mm Epsilon EP Drive DimensionsEIO26 Cable Cable DiagramsXTMDS-XXX Cable XV Motor CablesXCMDS-XXX XCMDBS-XXX +24V XTBMS-XXXPIN XEFTS-XXX CableXEFCS-XXX Cable CMDS-XXX Cable NT and MG Motor CablesCMMS-XXX Cable CBMS-XXX Cable Socket SpecificationsEFCS-XXX Cable SNCFLOA-XXX Sync CablesSNCMD-815-XXX SNCMD-89-XXX ESA-SP-485-XXX Communications CablesIndex Page