Cisco Systems ONS 15600 SDH manual 18-55, Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing

Page 55

Chapter 18 DLPs F300 to F399

DLP- F349 Install Fiber-Optic Cables for MS-SPRing Configurations

Caution Do not provision the MS-SPRing east and west ports on the same STM-N card.

Note To avoid error, connect fiber-optic cable so that the farthest slot to the right represents the east port, and the farthest slot to the left represents the west port. Fiber connected to an east port at one node must plug into the west port on an adjacent node.

Note See Table 16-1 on page 16-19and Table 16-2 on page 16-19for OGI connector pinouts of STM-N cards.

Step 1 Plan your fiber connections. Use the same plan for all MS-SPRing nodes. MS-SPRing configuration is achieved by correctly cabling the transmit and receive fibers of each node to the others.

Step 2 Plug the fiber into the Tx connector of an STM-N port at one node and plug the other end into the Rx connector of an STM-N port at the adjacent node. The card displays an SF LED if the transmit and receive fibers are mismatched.

Step 3 Repeat Step 2 until you have configured the ring.

Figure 18-11shows fiber connections for a two-fiber MS-SPRing with trunk ports in Slot 2, Port 7 (west) and Slot 12, Port 11 (east).

Figure 18-11 Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing

West

						Tx	Tx
						Rx	Rx
						Rx	Rx

		Slot 2					Slot 12
	Port 7						Port 11

Node 1

EastWest

Tx

Tx

Rx

Rx

Slot 2

Slot 12

Port 7

Port 11

Node 2

East

West

Tx	Tx	Tx	Tx
Rx	Rx	Rx	Rx
	East	West
Slot 2	Slot 12	Slot 2	Slot 12
Port 7	Port 11	Port 7	Port 11
	Node 4		Node 3

East

134293

Note To provision an MS-SPRing, see Chapter 5, “Turn Up a Network”

		Cisco ONS 15600 SDH Procedure Guide, R8.0
		Cisco ONS 15600 SDH Procedure Guide, R8.0
	October 2007			18-55
	October 2007			18-55

Image 55

Contents 18-1 DLP-F300 Install Fiber-Optic Cables for Sncp Configurations18-2 DLP-F302 Change Tunnel TypeClick the Provisioning Overhead Circuits tabs DLP-F303 Delete Overhead Circuits18-3 18-4 DLP-F304 Repair an IP Tunnel18-5 J1 Function CardsSelecting the Edit Path Trace Option 18-618-7 Click Circuits DLP-F306 Provision Path Trace on STM-N Ports18-8 18-9 DLP-F307 Create Login Node GroupsClick the Login Node Group tab Click Create Group18-10 Tools18-11 DLP-F310 Change the JRE Version18-12 DLP-F311 Remove Pass-through ConnectionsDLP-F313 Change a Circuit Service State DLP-F312 Delete a Node from a Specified Login Node Group18-13 18-14 DLP-F314 Provision MS-DCC Terminations18-15 Node view, click the Provisioning Comm Channels MS-DCC tabsClick the Provisioning Network Proxy subtabs DLP-F315 Provision a Proxy Tunnel18-16 Click the Provisioning Network Firewall subtabs DLP-F316 Provision a Firewall Tunnel18-17 DLP-F318 Delete a Firewall Tunnel DLP-F317 Delete a Proxy Tunnel18-18 Click the Provisioning Comm Channels MS-DCC tabs DLP-F319 Change an RS-DCC TerminationDLP-F320 Change an MS-DCC Termination Click the Provisioning Comm Channels RS-DCC tabs18-20 DLP-F321 Delete an RS-DCC TerminationDLP-F322 Delete an MS-DCC Termination Node view, click the Provisioning Comm Channel RS-DCC tabs18-21 Click the Provisioning Comm Channel MS-DCC tabsClick the Provisioning Ethernet Ports tabs DLP-F324 Provision Asap Ethernet Ports18-22 18-23 DLP-F325 Provision Asap POS PortsClick the Performance Ethernet Ether Ports Statistics tabs Click the Provisioning Ethernet POS Ports tabs18-24 DLP-F326 View Asap STM-N PM ParametersClick the Performance Ethernet POS Ports Statistics tabs Click the Performance Optical tabs Figure18-25 DLP-F327 View Asap Ether Ports Statistics PM ParametersEther Ports Statistics in the Card View Performance Window 18-2618-27 DLP-F328 View Asap Ether Ports Utilization PM Parameters18-28 DLP-F329 View Asap POS Ports Statistics PM Parameters18-29 DLP-F330 View Asap POS Ports Utilization PM Parameters18-30 DLP-F331 View Asap POS Ports History PM Parameters18-31 DLP-F332 Change Node Access and PM Clearing Privilege18-32 18-33 DLP-F333 Install the Asap Carrier Modules18-34 DLP-F334 Verify Pass-Through Circuits18-35 DLP-F335 Preprovision an SFP18-36 DLP-F336 Print CTC Data18-37 DLP-F337 View Asap Ether Ports History PM Parameters18-38 Click Create MS-SPRing Click the Provisioning MS-SPRing tabs18-39 18-40 DLP-F339 Create a Two-Fiber MS-SPRing Manually18-41 DLP-F340 Change an MS-SPRing Node ID18-42 DLP-F341 MS-SPRing Exercise Ring Test18-43 DLP-F342 MS-SPRing Switch TestClick Retrieve Click the Maintenance MS-SPRing tabs18-44 18-45 18-46 DLP-F343 Provision an STM-N Circuit Route DLP-F344 Initiate an MS-SPRing Manual Ring Switch18-47 Onsite/Remote Onsite Security Level Provisioning or higher DLP-F345 Clear an MS-SPRing Manual Ring Switch18-48 18-49 DLP-F346 Create an MS-SPRing on a Single Node18-50 DLP-F347 Initiate an MS-SPRing Force Ring Switch18-51 DLP-F348 View Circuit InformationSncp 2F-PCADRI PCA18-53 Droppending Pendingmerge18-54 18-55 11 Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing18-56 DLP-F350 Delete an MS-SPRing from a Single Node12 Selecting Single Roll Attributes 18-5714 Selecting a New Endpoint 18-5815 Viewing the Rolls Tab 18-5918-60 18-61 18-62 Click the Circuits tab17 Selecting Dual Roll Attributes 18-6318-64 18 Setting Roll Routing Preferences18-65 18-66 18-67 18-68 Click the Circuits Rolls tabs DLP-F356 Delete a Roll18-69 DLP-F358 Provision a Multirate PPM DLP-F357 Cancel a Roll18-70 Click the Provisioning Pluggable Port Modules tabs DLP-F359 Change the Optical Line Rate18-71 18-72 DLP-F360 Delete a PPM18-73 DLP-F361 Provision OSI Routing ModeDLP-F362 Provision or Modify Tarp Operating Parameters Node view, click the Provisioning OSI Tarp Config tabs18-74 18-75 Click Add Static Entry Node view, click the Provisioning OSI Tarp Static TDC tabs18-76 Click Delete Static Entry DLP-F365 Add a Tarp Manual Adjacency Table Entry18-77 DLP-F366 Provision OSI Routers Click the Provisioning OSI Routers Setup tabs18-78 DLP-F367 Provision Additional Manual Area Addresses DLP-F368 Enable the OSI Subnet on the LAN Interface18-79 Click the Provisioning OSI Tunnels tabs DLP-F369 Create an IP-Over-CLNS Tunnel18-80 18-81 DLP-F370 Remove a Tarp Manual Adjacency Table Entry18-82 DLP-F371 Change the OSI Routing Mode18-83 DLP-F372 Edit the OSI Router Configuration18-84 DLP-F373 Edit the OSI Subnetwork Point of AttachmentDLP-F374 Edit an IP-Over-CLNS Tunnel Node view, click the Provisioning OSI Routers Subnet tabs18-85 DLP-F375 Delete an IP-Over-CLNS Tunnel18-86 DLP-F376 View IS-IS Routing Information BaseDLP-F378 Manage the Tarp Data Cache DLP-F377 View ES-IS Routing Information Base18-87 18-88 DLP-F379 Export CTC Data19 Selecting CTC Data for Export 18-8918-90 DLP-F380 Configure the Node for Radius Authentication20 Radius Server Tab 18-91Click the Provisioning Server Trails tabs DLP-F381 Delete a Server Trail18-92 DLP-F382 Grant Superuser Privileges to a Provisioning User DLP-F383 Download an Alarm Severity Profile18-93 18-94 18-95 DLP-F384 Install the Asap 1PIO and 4PIO PIM Modules22 1PIO Module Faceplate 18-9618-97 DLP-F385 Consolidate Links in Network View18-98 24shows a network view with unconsolidated DCC and PPC linksDwdm GCC, OTS, PPC TDM ALL18-99 DLP-F387 Install an SFP/XFP DLP-F386 Adjust the Java Virtual Memory Heap Size18-100 18-101 DLP-F388 Remove an SFP/XFP18-102 DLP-F389 Remove a 1PIO or 4PIO PIM ModuleClick the Provisioning Optical Line tabs DLP-F390 Provision an Optical Line Rate and WavelengthAsap 4PIO 1PIOCAP/CAP2 DLP-F391 Install Alarm Wires on the CAP/CAP218-104 27 Rear of the ONS 15600 SDH, Including the CAP/CAP2 18-10528 CAP/CAP2 Faceplate and Connections 18-10618-107 DLP-F392 Change Line Transmission Settings for STM-N CardsSD BER SF BER18-108 18-109 SonetSTU Sets18-110 18-111 DLP-F393 Change Threshold Settings for STM-N Ports18-112 18-113 DLP-F394 Change Optics Threshold Settings for STM-N Ports18-114 RefreshClick the Maintenance ALS tabs DLP-F395 Change the STM-N Port ALS Maintenance Settings18-115 18-116 DLP-F396 Clear All PM Thresholds18-117 DLP-F397 Provision the Designated Socks Servers18-118 18-119 18-120