Page 65
Chapter 18 DLPs F300 to F399
DLP- F353 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing
Step 16 If you checked Review Route Before Creation in Step 12:
a.In the Roll Route Review and Edit area, review the circuit route. To add or delete a circuit span, select a node on the circuit route. Blue arrows show the circuit route. Green arrows indicate spans that you can add. Click a span arrowhead, then click Include to include the span or Remove to remove the span.
b.If the provisioned circuit does not reflect the routing and configuration you want, click Back to verify and change circuit information.
Step 17 Click Finish.
In the Circuits tab, verify that a new circuit appears. This circuit is the Roll To circuit. It is designated with the Roll From circuit name appended with ROLL**.
Step 18 Click the Rolls tab. Two new rolls now appear. For each pending roll, view the Roll Valid Signal status. When one of the following requirements is met, continue with Step 19.
•If the Roll Valid Signal status is true, a valid signal was found on the new port.
•If the Roll Valid Signal status is false, a valid signal was not found. Wait until the signal is found before continuing with the next step. If a valid signal is not found, refer to the Cisco
ONS 15600 SDH Troubleshooting Guide. To cancel the roll, see the “DLP-F357 Cancel a Roll” task on page 18-70.
•The roll is a one-way destination roll and the Roll Valid signal status is false. It is not possible to get a Roll Valid Signal status of true for a one-way destination roll.
Note If you have completed a roll, you cannot cancel the sibling roll. You must cancel the two rolls together.
Note You cannot cancel an automatic roll after a valid signal is found.
•A roll can be forced onto the Roll To Circuit destination without a valid signal by using the Force Valid Signal button. If you choose Force Valid Signal, traffic on the circuit that is involved in the roll will be dropped once the roll is completed.
Step 19 If you selected Manual in Step 5, click both rolls on the Rolls tab and click Complete to route the traffic to the new port. If you selected Auto, continue with Step 20.
Note You cannot complete a roll if you cancelled the sibling roll. You must complete the two rolls together.
Step 20 For both manual and automatic rolls, click Finish to complete circuit roll process.
Step 21 Return to your originating procedure (NTP).
| | Cisco ONS 15600 SDH Procedure Guide, R8.0 | | |
| | |
| October 2007 | | | 18-65 | |
| | | |
Contents
18-1
DLP-F300 Install Fiber-Optic Cables for Sncp Configurations
18-2
DLP-F302 Change Tunnel Type
18-3
DLP-F303 Delete Overhead Circuits
Click the Provisioning Overhead Circuits tabs
18-4
DLP-F304 Repair an IP Tunnel
18-5
J1 Function Cards
Selecting the Edit Path Trace Option
18-6
18-7
18-8
DLP-F306 Provision Path Trace on STM-N Ports
Click Circuits
Click the Login Node Group tab
DLP-F307 Create Login Node Groups
Click Create Group
18-9
18-10
Tools
18-11
DLP-F310 Change the JRE Version
18-12
DLP-F311 Remove Pass-through Connections
18-13
DLP-F312 Delete a Node from a Specified Login Node Group
DLP-F313 Change a Circuit Service State
18-14
DLP-F314 Provision MS-DCC Terminations
18-15
Node view, click the Provisioning Comm Channels MS-DCC tabs
18-16
DLP-F315 Provision a Proxy Tunnel
Click the Provisioning Network Proxy subtabs
18-17
DLP-F316 Provision a Firewall Tunnel
Click the Provisioning Network Firewall subtabs
18-18
DLP-F317 Delete a Proxy Tunnel
DLP-F318 Delete a Firewall Tunnel
DLP-F320 Change an MS-DCC Termination
DLP-F319 Change an RS-DCC Termination
Click the Provisioning Comm Channels RS-DCC tabs
Click the Provisioning Comm Channels MS-DCC tabs
DLP-F322 Delete an MS-DCC Termination
DLP-F321 Delete an RS-DCC Termination
Node view, click the Provisioning Comm Channel RS-DCC tabs
18-20
18-21
Click the Provisioning Comm Channel MS-DCC tabs
18-22
DLP-F324 Provision Asap Ethernet Ports
Click the Provisioning Ethernet Ports tabs
Click the Performance Ethernet Ether Ports Statistics tabs
DLP-F325 Provision Asap POS Ports
Click the Provisioning Ethernet POS Ports tabs
18-23
Click the Performance Ethernet POS Ports Statistics tabs
DLP-F326 View Asap STM-N PM Parameters
Click the Performance Optical tabs Figure
18-24
18-25
DLP-F327 View Asap Ether Ports Statistics PM Parameters
Ether Ports Statistics in the Card View Performance Window
18-26
18-27
DLP-F328 View Asap Ether Ports Utilization PM Parameters
18-28
DLP-F329 View Asap POS Ports Statistics PM Parameters
18-29
DLP-F330 View Asap POS Ports Utilization PM Parameters
18-30
DLP-F331 View Asap POS Ports History PM Parameters
18-31
DLP-F332 Change Node Access and PM Clearing Privilege
18-32
18-33
DLP-F333 Install the Asap Carrier Modules
18-34
DLP-F334 Verify Pass-Through Circuits
18-35
DLP-F335 Preprovision an SFP
18-36
DLP-F336 Print CTC Data
18-37
DLP-F337 View Asap Ether Ports History PM Parameters
18-38
18-39
Click the Provisioning MS-SPRing tabs
Click Create MS-SPRing
18-40
DLP-F339 Create a Two-Fiber MS-SPRing Manually
18-41
DLP-F340 Change an MS-SPRing Node ID
18-42
DLP-F341 MS-SPRing Exercise Ring Test
18-43
DLP-F342 MS-SPRing Switch Test
18-44
Click the Maintenance MS-SPRing tabs
Click Retrieve
18-45
18-46
18-47
DLP-F344 Initiate an MS-SPRing Manual Ring Switch
DLP-F343 Provision an STM-N Circuit Route
18-48
DLP-F345 Clear an MS-SPRing Manual Ring Switch
Onsite/Remote Onsite Security Level Provisioning or higher
18-49
DLP-F346 Create an MS-SPRing on a Single Node
18-50
DLP-F347 Initiate an MS-SPRing Force Ring Switch
18-51
DLP-F348 View Circuit Information
DRI
2F-PCA
PCA
Sncp
18-53
18-54
Pendingmerge
Droppending
18-55
11 Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing
18-56
DLP-F350 Delete an MS-SPRing from a Single Node
12 Selecting Single Roll Attributes
18-57
14 Selecting a New Endpoint
18-58
15 Viewing the Rolls Tab
18-59
18-60
18-61
18-62
Click the Circuits tab
17 Selecting Dual Roll Attributes
18-63
18-64
18 Setting Roll Routing Preferences
18-65
18-66
18-67
18-68
18-69
DLP-F356 Delete a Roll
Click the Circuits Rolls tabs
18-70
DLP-F357 Cancel a Roll
DLP-F358 Provision a Multirate PPM
18-71
DLP-F359 Change the Optical Line Rate
Click the Provisioning Pluggable Port Modules tabs
18-72
DLP-F360 Delete a PPM
18-73
DLP-F361 Provision OSI Routing Mode
18-74
Node view, click the Provisioning OSI Tarp Config tabs
DLP-F362 Provision or Modify Tarp Operating Parameters
18-75
18-76
Node view, click the Provisioning OSI Tarp Static TDC tabs
Click Add Static Entry
18-77
DLP-F365 Add a Tarp Manual Adjacency Table Entry
Click Delete Static Entry
18-78
Click the Provisioning OSI Routers Setup tabs
DLP-F366 Provision OSI Routers
18-79
DLP-F368 Enable the OSI Subnet on the LAN Interface
DLP-F367 Provision Additional Manual Area Addresses
18-80
DLP-F369 Create an IP-Over-CLNS Tunnel
Click the Provisioning OSI Tunnels tabs
18-81
DLP-F370 Remove a Tarp Manual Adjacency Table Entry
18-82
DLP-F371 Change the OSI Routing Mode
18-83
DLP-F372 Edit the OSI Router Configuration
DLP-F374 Edit an IP-Over-CLNS Tunnel
DLP-F373 Edit the OSI Subnetwork Point of Attachment
Node view, click the Provisioning OSI Routers Subnet tabs
18-84
18-85
DLP-F375 Delete an IP-Over-CLNS Tunnel
18-86
DLP-F376 View IS-IS Routing Information Base
18-87
DLP-F377 View ES-IS Routing Information Base
DLP-F378 Manage the Tarp Data Cache
18-88
DLP-F379 Export CTC Data
19 Selecting CTC Data for Export
18-89
18-90
DLP-F380 Configure the Node for Radius Authentication
20 Radius Server Tab
18-91
18-92
DLP-F381 Delete a Server Trail
Click the Provisioning Server Trails tabs
18-93
DLP-F383 Download an Alarm Severity Profile
DLP-F382 Grant Superuser Privileges to a Provisioning User
18-94
18-95
DLP-F384 Install the Asap 1PIO and 4PIO PIM Modules
22 1PIO Module Faceplate
18-96
18-97
DLP-F385 Consolidate Links in Network View
18-98
24shows a network view with unconsolidated DCC and PPC links
18-99
ALL
Dwdm GCC, OTS, PPC TDM
18-100
DLP-F386 Adjust the Java Virtual Memory Heap Size
DLP-F387 Install an SFP/XFP
18-101
DLP-F388 Remove an SFP/XFP
18-102
DLP-F389 Remove a 1PIO or 4PIO PIM Module
Asap 4PIO
DLP-F390 Provision an Optical Line Rate and Wavelength
1PIO
Click the Provisioning Optical Line tabs
18-104
DLP-F391 Install Alarm Wires on the CAP/CAP2
CAP/CAP2
27 Rear of the ONS 15600 SDH, Including the CAP/CAP2
18-105
28 CAP/CAP2 Faceplate and Connections
18-106
18-107
DLP-F392 Change Line Transmission Settings for STM-N Cards
18-108
SF BER
SD BER
18-109
Sonet
18-110
Sets
STU
18-111
DLP-F393 Change Threshold Settings for STM-N Ports
18-112
18-113
DLP-F394 Change Optics Threshold Settings for STM-N Ports
18-114
Refresh
18-115
DLP-F395 Change the STM-N Port ALS Maintenance Settings
Click the Maintenance ALS tabs
18-116
DLP-F396 Clear All PM Thresholds
18-117
DLP-F397 Provision the Designated Socks Servers
18-118
18-119
18-120