Cisco Systems ONS 15600 SDH Node view, click the Provisioning OSI Tarp Static TDC tabs, 18-76

Page 76

Chapter 18 DLPs F300 to F399

DLP- F363 Add a Static TID-to-NSAP Entry to the TARP Data Cache

•LDB Flush—Sets the frequency period for flushing the LDB. The default is 5 minutes. The range is 0 to 1440 minutes.

•T1—Sets the amount of time to wait for a response to a Type 1 PDU. Type 1 PDUs seek a specific NE TID within an OSI Level 1 area. The default is 15 seconds. The range is 0 to 3600 seconds.

•T2—Sets the amount of time to wait for a response to a Type 2 PDU. TARP Type 2 PDUs seek a specific NE TID value within OSI Level 1 and Level 2 areas. The default is 25 seconds. The range is 0 to 3600 seconds.

•T3—Sets the amount of time to wait for an address resolution request. The default is 40 seconds. The range is 0 to 3600 seconds.

•T4—Sets the amount of time to wait for an error recovery. This timer begins after the T2 timer expires without finding the requested NE TID. The default is 20 seconds. The range is

0 to 3600 seconds.

Note Timers T1, T2, and T4 are not used if TARP PDUs Origination is not enabled.

Step 3 Click Apply.

Step 4 Return to your originating procedure (NTP).

DLP-F363 Add a Static TID-to-NSAP Entry to the TARP Data Cache

	Purpose	This task adds a static TID-to-NSAP entry to the TDC. The static entries
		are required for NEs that do not support TARP and are similar to static
		routes. For a specific TID, you must force a specific NSAP.
	Tools/Equipment	None
	Prerequisite procedures	DLP-F181 Log into CTC, page 16-34
	Required/As needed	As needed
	Onsite/Remote	Onsite or remote
	Security Level	Provisioner or higher

Step 1	In node view, click the Provisioning > OSI > TARP > Static TDC tabs.
Step 2	Click Add Static Entry.
Step 3	In the Add Static Entry dialog box, enter the following:

•TID—Enter the TID of the NE. (For ONS nodes, the TID is the Node Name parameter on the node view Provisioning > General tab.)

•NSAP—Enter the OSI NSAP address in the NSAP field or, if preferred, click Use Mask and enter the address in the Masked NSAP Entry dialog box.

Step 4 Click OK to close the Masked NSAP Entry dialog box, if used, and then click OK to close the Add Static Entry dialog box.

Step 5 Return to your originating procedure (NTP).

	Cisco ONS 15600 SDH Procedure Guide, R8.0
18-76	October 2007

Image 76

Contents DLP-F300 Install Fiber-Optic Cables for Sncp Configurations 18-1DLP-F302 Change Tunnel Type 18-2Click the Provisioning Overhead Circuits tabs DLP-F303 Delete Overhead Circuits18-3 DLP-F304 Repair an IP Tunnel 18-4J1 Function Cards 18-518-6 Selecting the Edit Path Trace Option18-7 Click Circuits DLP-F306 Provision Path Trace on STM-N Ports18-8 DLP-F307 Create Login Node Groups Click the Login Node Group tabClick Create Group 18-9Tools 18-10DLP-F310 Change the JRE Version 18-11DLP-F311 Remove Pass-through Connections 18-12DLP-F313 Change a Circuit Service State DLP-F312 Delete a Node from a Specified Login Node Group18-13 DLP-F314 Provision MS-DCC Terminations 18-14Node view, click the Provisioning Comm Channels MS-DCC tabs 18-15Click the Provisioning Network Proxy subtabs DLP-F315 Provision a Proxy Tunnel18-16 Click the Provisioning Network Firewall subtabs DLP-F316 Provision a Firewall Tunnel18-17 DLP-F318 Delete a Firewall Tunnel DLP-F317 Delete a Proxy Tunnel18-18 DLP-F319 Change an RS-DCC Termination DLP-F320 Change an MS-DCC TerminationClick the Provisioning Comm Channels RS-DCC tabs Click the Provisioning Comm Channels MS-DCC tabsDLP-F321 Delete an RS-DCC Termination DLP-F322 Delete an MS-DCC TerminationNode view, click the Provisioning Comm Channel RS-DCC tabs 18-20Click the Provisioning Comm Channel MS-DCC tabs 18-21Click the Provisioning Ethernet Ports tabs DLP-F324 Provision Asap Ethernet Ports18-22 DLP-F325 Provision Asap POS Ports Click the Performance Ethernet Ether Ports Statistics tabsClick the Provisioning Ethernet POS Ports tabs 18-23DLP-F326 View Asap STM-N PM Parameters Click the Performance Ethernet POS Ports Statistics tabsClick the Performance Optical tabs Figure 18-24DLP-F327 View Asap Ether Ports Statistics PM Parameters 18-2518-26 Ether Ports Statistics in the Card View Performance WindowDLP-F328 View Asap Ether Ports Utilization PM Parameters 18-27DLP-F329 View Asap POS Ports Statistics PM Parameters 18-28DLP-F330 View Asap POS Ports Utilization PM Parameters 18-29DLP-F331 View Asap POS Ports History PM Parameters 18-30DLP-F332 Change Node Access and PM Clearing Privilege 18-3118-32 DLP-F333 Install the Asap Carrier Modules 18-33DLP-F334 Verify Pass-Through Circuits 18-34DLP-F335 Preprovision an SFP 18-35DLP-F336 Print CTC Data 18-36DLP-F337 View Asap Ether Ports History PM Parameters 18-3718-38 Click Create MS-SPRing Click the Provisioning MS-SPRing tabs18-39 DLP-F339 Create a Two-Fiber MS-SPRing Manually 18-40DLP-F340 Change an MS-SPRing Node ID 18-41DLP-F341 MS-SPRing Exercise Ring Test 18-42DLP-F342 MS-SPRing Switch Test 18-43Click Retrieve Click the Maintenance MS-SPRing tabs18-44 18-45 18-46 DLP-F343 Provision an STM-N Circuit Route DLP-F344 Initiate an MS-SPRing Manual Ring Switch18-47 Onsite/Remote Onsite Security Level Provisioning or higher DLP-F345 Clear an MS-SPRing Manual Ring Switch18-48 DLP-F346 Create an MS-SPRing on a Single Node 18-49DLP-F347 Initiate an MS-SPRing Force Ring Switch 18-50DLP-F348 View Circuit Information 18-512F-PCA DRIPCA Sncp18-53 Droppending Pendingmerge18-54 11 Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing 18-55DLP-F350 Delete an MS-SPRing from a Single Node 18-5618-57 12 Selecting Single Roll Attributes18-58 14 Selecting a New Endpoint18-59 15 Viewing the Rolls Tab18-60 18-61 Click the Circuits tab 18-6218-63 17 Selecting Dual Roll Attributes18 Setting Roll Routing Preferences 18-6418-65 18-66 18-67 18-68 Click the Circuits Rolls tabs DLP-F356 Delete a Roll18-69 DLP-F358 Provision a Multirate PPM DLP-F357 Cancel a Roll18-70 Click the Provisioning Pluggable Port Modules tabs DLP-F359 Change the Optical Line Rate18-71 DLP-F360 Delete a PPM 18-72DLP-F361 Provision OSI Routing Mode 18-73DLP-F362 Provision or Modify Tarp Operating Parameters Node view, click the Provisioning OSI Tarp Config tabs18-74 18-75 Click Add Static Entry Node view, click the Provisioning OSI Tarp Static TDC tabs18-76 Click Delete Static Entry DLP-F365 Add a Tarp Manual Adjacency Table Entry18-77 DLP-F366 Provision OSI Routers Click the Provisioning OSI Routers Setup tabs18-78 DLP-F367 Provision Additional Manual Area Addresses DLP-F368 Enable the OSI Subnet on the LAN Interface18-79 Click the Provisioning OSI Tunnels tabs DLP-F369 Create an IP-Over-CLNS Tunnel18-80 DLP-F370 Remove a Tarp Manual Adjacency Table Entry 18-81DLP-F371 Change the OSI Routing Mode 18-82DLP-F372 Edit the OSI Router Configuration 18-83DLP-F373 Edit the OSI Subnetwork Point of Attachment DLP-F374 Edit an IP-Over-CLNS TunnelNode view, click the Provisioning OSI Routers Subnet tabs 18-84DLP-F375 Delete an IP-Over-CLNS Tunnel 18-85DLP-F376 View IS-IS Routing Information Base 18-86DLP-F378 Manage the Tarp Data Cache DLP-F377 View ES-IS Routing Information Base18-87 DLP-F379 Export CTC Data 18-8818-89 19 Selecting CTC Data for ExportDLP-F380 Configure the Node for Radius Authentication 18-9018-91 20 Radius Server TabClick the Provisioning Server Trails tabs DLP-F381 Delete a Server Trail18-92 DLP-F382 Grant Superuser Privileges to a Provisioning User DLP-F383 Download an Alarm Severity Profile18-93 18-94 DLP-F384 Install the Asap 1PIO and 4PIO PIM Modules 18-9518-96 22 1PIO Module FaceplateDLP-F385 Consolidate Links in Network View 18-9724shows a network view with unconsolidated DCC and PPC links 18-98Dwdm GCC, OTS, PPC TDM ALL18-99 DLP-F387 Install an SFP/XFP DLP-F386 Adjust the Java Virtual Memory Heap Size18-100 DLP-F388 Remove an SFP/XFP 18-101DLP-F389 Remove a 1PIO or 4PIO PIM Module 18-102DLP-F390 Provision an Optical Line Rate and Wavelength Asap 4PIO1PIO Click the Provisioning Optical Line tabsCAP/CAP2 DLP-F391 Install Alarm Wires on the CAP/CAP218-104 18-105 27 Rear of the ONS 15600 SDH, Including the CAP/CAP218-106 28 CAP/CAP2 Faceplate and ConnectionsDLP-F392 Change Line Transmission Settings for STM-N Cards 18-107SD BER SF BER18-108 Sonet 18-109STU Sets18-110 DLP-F393 Change Threshold Settings for STM-N Ports 18-11118-112 DLP-F394 Change Optics Threshold Settings for STM-N Ports 18-113Refresh 18-114Click the Maintenance ALS tabs DLP-F395 Change the STM-N Port ALS Maintenance Settings18-115 DLP-F396 Clear All PM Thresholds 18-116DLP-F397 Provision the Designated Socks Servers 18-11718-118 18-119 18-120