Cisco Systems ONS 15600 SDH manual DLP-F346 Create an MS-SPRing on a Single Node, 18-49

Page 49

Chapter 18 DLPs F300 to F399

DLP- F346 Create an MS-SPRing on a Single Node

Tip To move an icon to a new location, for example, to see MS-SPRing channel (port) information more clearly, click an icon on the Edit MS-SPRing network graphic and while pressing Ctrl, drag the icon to a new location.

Step 4 Right-click the MS-SPRing node channel (port) where the manual ring switch was applied and choose Set West Protection Operation or Set East Protection Operation, as applicable.

Step 5 In the dialog box, choose CLEAR from the drop-down list. Click OK.

Step 6 Click Yes in the Confirm MS-SPRing Operation dialog box. The letter “M” is removed from the channel (port) and the span turns green on the network view map.

Step 7 From the File menu, choose Close.

Step 8 Return to your originating procedure (NTP).

DLP-F346 Create an MS-SPRing on a Single Node

 

Purpose

This task creates an MS-SPRing on a single node. Use this task to add a

 

 

node to an existing MS-SPRing or to delete and then recreate an

 

 

MS-SPRing temporarily on one node.

 

Tools/Equipment

None

 

Prerequisite Procedures

DLP-F181 Log into CTC, page 16-34

 

Required/As Needed

As needed

 

Onsite/Remote

Onsite

 

Security Level

Provisioning or higher

 

 

Step 1

In node view, click the Provisioning > MS-SPRingtabs.

Step 2

In the Suggestion dialog box, click OK.

Step 3

In the Create MS-SPRing dialog box, enter the MS-SPRing information:

•Ring Type—Enter the ring type (2 Fiber) of the MS-SPRing.

•Ring Name—Enter the MS-SPRing name. If the node is being added to an MS-SPRing, use the MS-SPRing ring name.

•Node ID—Enter the node ID. If the node is being added to an MS-SPRing, use an ID that is not used by other MS-SPRing nodes in that ring.

•Ring Reversion—Enter the ring reversion time of the existing MS-SPRing.

•West Line—Enter the slot on the node that will connect to the existing MS-SPRing through the node’s west line (port).

•East Line—Enter the slot on the node that will connect to the existing MS-SPRing through the node’s east line (port).

Step 4 Click OK.

 

 

Cisco ONS 15600 SDH Procedure Guide, R8.0

 

 

 

 

 

 

October 2007

 

 

18-49

 

 

 

 

 

Page 48 Page 50
Image 49
Page 48 Page 50
Contents 18-1 DLP-F300 Install Fiber-Optic Cables for Sncp Configurations18-2 DLP-F302 Change Tunnel TypeClick the Provisioning Overhead Circuits tabs DLP-F303 Delete Overhead Circuits18-3 18-4 DLP-F304 Repair an IP Tunnel18-5 J1 Function CardsSelecting the Edit Path Trace Option 18-618-7 Click Circuits DLP-F306 Provision Path Trace on STM-N Ports18-8 Click the Login Node Group tab DLP-F307 Create Login Node GroupsClick Create Group 18-918-10 Tools18-11 DLP-F310 Change the JRE Version18-12 DLP-F311 Remove Pass-through ConnectionsDLP-F313 Change a Circuit Service State DLP-F312 Delete a Node from a Specified Login Node Group18-13 18-14 DLP-F314 Provision MS-DCC Terminations18-15 Node view, click the Provisioning Comm Channels MS-DCC tabsClick the Provisioning Network Proxy subtabs DLP-F315 Provision a Proxy Tunnel18-16 Click the Provisioning Network Firewall subtabs DLP-F316 Provision a Firewall Tunnel18-17 DLP-F318 Delete a Firewall Tunnel DLP-F317 Delete a Proxy Tunnel18-18 DLP-F320 Change an MS-DCC Termination DLP-F319 Change an RS-DCC TerminationClick the Provisioning Comm Channels RS-DCC tabs Click the Provisioning Comm Channels MS-DCC tabsDLP-F322 Delete an MS-DCC Termination DLP-F321 Delete an RS-DCC TerminationNode view, click the Provisioning Comm Channel RS-DCC tabs 18-2018-21 Click the Provisioning Comm Channel MS-DCC tabsClick the Provisioning Ethernet Ports tabs DLP-F324 Provision Asap Ethernet Ports18-22 Click the Performance Ethernet Ether Ports Statistics tabs DLP-F325 Provision Asap POS PortsClick the Provisioning Ethernet POS Ports tabs 18-23Click the Performance Ethernet POS Ports Statistics tabs DLP-F326 View Asap STM-N PM ParametersClick the Performance Optical tabs Figure 18-2418-25 DLP-F327 View Asap Ether Ports Statistics PM ParametersEther Ports Statistics in the Card View Performance Window 18-2618-27 DLP-F328 View Asap Ether Ports Utilization PM Parameters18-28 DLP-F329 View Asap POS Ports Statistics PM Parameters18-29 DLP-F330 View Asap POS Ports Utilization PM Parameters18-30 DLP-F331 View Asap POS Ports History PM Parameters18-31 DLP-F332 Change Node Access and PM Clearing Privilege18-32 18-33 DLP-F333 Install the Asap Carrier Modules18-34 DLP-F334 Verify Pass-Through Circuits18-35 DLP-F335 Preprovision an SFP18-36 DLP-F336 Print CTC Data18-37 DLP-F337 View Asap Ether Ports History PM Parameters18-38 Click Create MS-SPRing Click the Provisioning MS-SPRing tabs18-39 18-40 DLP-F339 Create a Two-Fiber MS-SPRing Manually18-41 DLP-F340 Change an MS-SPRing Node ID18-42 DLP-F341 MS-SPRing Exercise Ring Test18-43 DLP-F342 MS-SPRing Switch TestClick Retrieve Click the Maintenance MS-SPRing tabs18-44 18-45 18-46 DLP-F343 Provision an STM-N Circuit Route DLP-F344 Initiate an MS-SPRing Manual Ring Switch18-47 Onsite/Remote Onsite Security Level Provisioning or higher DLP-F345 Clear an MS-SPRing Manual Ring Switch18-48 18-49 DLP-F346 Create an MS-SPRing on a Single Node18-50 DLP-F347 Initiate an MS-SPRing Force Ring Switch18-51 DLP-F348 View Circuit InformationDRI 2F-PCAPCA Sncp18-53 Droppending Pendingmerge18-54 18-55 11 Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing18-56 DLP-F350 Delete an MS-SPRing from a Single Node12 Selecting Single Roll Attributes 18-5714 Selecting a New Endpoint 18-5815 Viewing the Rolls Tab 18-5918-60 18-61 18-62 Click the Circuits tab17 Selecting Dual Roll Attributes 18-6318-64 18 Setting Roll Routing Preferences18-65 18-66 18-67 18-68 Click the Circuits Rolls tabs DLP-F356 Delete a Roll18-69 DLP-F358 Provision a Multirate PPM DLP-F357 Cancel a Roll18-70 Click the Provisioning Pluggable Port Modules tabs DLP-F359 Change the Optical Line Rate18-71 18-72 DLP-F360 Delete a PPM18-73 DLP-F361 Provision OSI Routing ModeDLP-F362 Provision or Modify Tarp Operating Parameters Node view, click the Provisioning OSI Tarp Config tabs18-74 18-75 Click Add Static Entry Node view, click the Provisioning OSI Tarp Static TDC tabs18-76 Click Delete Static Entry DLP-F365 Add a Tarp Manual Adjacency Table Entry18-77 DLP-F366 Provision OSI Routers Click the Provisioning OSI Routers Setup tabs18-78 DLP-F367 Provision Additional Manual Area Addresses DLP-F368 Enable the OSI Subnet on the LAN Interface18-79 Click the Provisioning OSI Tunnels tabs DLP-F369 Create an IP-Over-CLNS Tunnel18-80 18-81 DLP-F370 Remove a Tarp Manual Adjacency Table Entry18-82 DLP-F371 Change the OSI Routing Mode18-83 DLP-F372 Edit the OSI Router ConfigurationDLP-F374 Edit an IP-Over-CLNS Tunnel DLP-F373 Edit the OSI Subnetwork Point of AttachmentNode view, click the Provisioning OSI Routers Subnet tabs 18-8418-85 DLP-F375 Delete an IP-Over-CLNS Tunnel18-86 DLP-F376 View IS-IS Routing Information BaseDLP-F378 Manage the Tarp Data Cache DLP-F377 View ES-IS Routing Information Base18-87 18-88 DLP-F379 Export CTC Data19 Selecting CTC Data for Export 18-8918-90 DLP-F380 Configure the Node for Radius Authentication20 Radius Server Tab 18-91Click the Provisioning Server Trails tabs DLP-F381 Delete a Server Trail18-92 DLP-F382 Grant Superuser Privileges to a Provisioning User DLP-F383 Download an Alarm Severity Profile18-93 18-94 18-95 DLP-F384 Install the Asap 1PIO and 4PIO PIM Modules22 1PIO Module Faceplate 18-9618-97 DLP-F385 Consolidate Links in Network View18-98 24shows a network view with unconsolidated DCC and PPC linksDwdm GCC, OTS, PPC TDM ALL18-99 DLP-F387 Install an SFP/XFP DLP-F386 Adjust the Java Virtual Memory Heap Size18-100 18-101 DLP-F388 Remove an SFP/XFP18-102 DLP-F389 Remove a 1PIO or 4PIO PIM ModuleAsap 4PIO DLP-F390 Provision an Optical Line Rate and Wavelength1PIO Click the Provisioning Optical Line tabsCAP/CAP2 DLP-F391 Install Alarm Wires on the CAP/CAP218-104 27 Rear of the ONS 15600 SDH, Including the CAP/CAP2 18-10528 CAP/CAP2 Faceplate and Connections 18-10618-107 DLP-F392 Change Line Transmission Settings for STM-N CardsSD BER SF BER18-108 18-109 SonetSTU Sets18-110 18-111 DLP-F393 Change Threshold Settings for STM-N Ports18-112 18-113 DLP-F394 Change Optics Threshold Settings for STM-N Ports18-114 RefreshClick the Maintenance ALS tabs DLP-F395 Change the STM-N Port ALS Maintenance Settings18-115 18-116 DLP-F396 Clear All PM Thresholds18-117 DLP-F397 Provision the Designated Socks Servers18-118 18-119 18-120
Top Page Image Contents