Cisco Systems ONS 15600 SDH Click the Provisioning MS-SPRing tabs, Click Create MS-SPRing, 18-39

Page 39

Chapter 18 DLPs F300 to F399

DLP- F338 Create a Two-Fiber MS-SPRing Using the MS-SPRing Wizard

 

Onsite/Remote

Onsite or remote

 

Security Level

Provisioning or higher

 

 

Step 1

From the View menu, choose Go to Network View.

Step 2

Click the Provisioning > MS-SPRing tabs.

Step 3

Click Create MS-SPRing.

 

Step 4

In the MS-SPRing Creation dialog box, set the MS-SPRing properties:

•Ring Type—Choose two-fiber.

•Speed—Choose the MS-SPRing ring speed: STM-4, STM-16, or STM-64. The speed must match the STM-N speed of the MS-SPRing trunk (span) ports.

•Ring Name—Assign a ring name. The name can be from 1 to 6 characters in length. Any alphanumeric string is permissible, and uppercase and lowercase letters can be combined. Do not use the character string All in either uppercase or lowercase letters; this is a TL1 keyword and will be rejected. Do not choose a name that is already assigned to another MS-SPRing.

•Reversion time—Set the amount of time that will pass before the traffic reverts to the original working path following a ring switch. The default is 5 minutes. Ring reversion can be set to Never.

Step 5 Click Next. If the network graphic appears, go to Step 6.

If CTC determines that an MS-SPRing cannot be created, for example, not enough optical cards are installed or it finds circuits with SNCP selectors, a “Cannot Create MS-SPRing” message appears. If this occurs, complete the following steps:

a.Click OK.

b.In the Create MS-SPRing window, click Excluded Nodes. Review the information explaining why the MS-SPRing could not be created, then click OK.

c.Depending on the problem, click Back to start over or click Cancel to cancel the operation.

d.Complete the NTP-F147 Provision MS-SPRing Nodes, page 5-6, making sure all steps are completed accurately, then start this procedure again.

Step 6 In the network graphic, double-click an MS-SPRing span line. If the span line is DCC-connected to other MS-SPRing ports that constitute a complete ring, the lines turn blue. If the lines do not form a complete ring, double-click the span lines until a complete ring is formed. When the ring is DCC-connected, go to Step 7.

Step 7 Click Finish. If the MS-SPRing window appears with the MS-SPRing you created, go to Step 8. If a “Cannot Create MS-SPRing” or “Error While Creating MS-SPRing” message appears:

a.Click OK.

b.In the Create MS-SPRing window, click Excluded Nodes. Review the information explaining why the MS-SPRing could not be created, then click OK.

c.Depending on the problem, click Back to start over or click Cancel to cancel the operation.

d.Complete the NTP-F147 Provision MS-SPRing Nodes, page 5-6, making sure all steps are completed accurately, then start this procedure again.

Note Some or all of the following alarms might briefly appear during MS-SPRing setup: E-W-MISMATCH, RING-MISMATCH, APSCIMP, APSCDFLTK, and MSSP-OOSYNC.

Step 8 Verify the following:

 

 

Cisco ONS 15600 SDH Procedure Guide, R8.0

 

 

 

 

 

 

October 2007

 

 

18-39

 

 

 

 

 

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 18-1 DLP-F300 Install Fiber-Optic Cables for Sncp Configurations18-2 DLP-F302 Change Tunnel TypeDLP-F303 Delete Overhead Circuits Click the Provisioning Overhead Circuits tabs18-3 18-4 DLP-F304 Repair an IP Tunnel18-5 J1 Function CardsSelecting the Edit Path Trace Option 18-618-7 DLP-F306 Provision Path Trace on STM-N Ports Click Circuits18-8 18-9 DLP-F307 Create Login Node GroupsClick the Login Node Group tab Click Create Group18-10 Tools18-11 DLP-F310 Change the JRE Version18-12 DLP-F311 Remove Pass-through ConnectionsDLP-F312 Delete a Node from a Specified Login Node Group DLP-F313 Change a Circuit Service State18-13 18-14 DLP-F314 Provision MS-DCC Terminations18-15 Node view, click the Provisioning Comm Channels MS-DCC tabsDLP-F315 Provision a Proxy Tunnel Click the Provisioning Network Proxy subtabs18-16 DLP-F316 Provision a Firewall Tunnel Click the Provisioning Network Firewall subtabs18-17 DLP-F317 Delete a Proxy Tunnel DLP-F318 Delete a Firewall Tunnel18-18 Click the Provisioning Comm Channels MS-DCC tabs DLP-F319 Change an RS-DCC TerminationDLP-F320 Change an MS-DCC Termination Click the Provisioning Comm Channels RS-DCC tabs18-20 DLP-F321 Delete an RS-DCC TerminationDLP-F322 Delete an MS-DCC Termination Node view, click the Provisioning Comm Channel RS-DCC tabs18-21 Click the Provisioning Comm Channel MS-DCC tabsDLP-F324 Provision Asap Ethernet Ports Click the Provisioning Ethernet Ports tabs18-22 18-23 DLP-F325 Provision Asap POS PortsClick the Performance Ethernet Ether Ports Statistics tabs Click the Provisioning Ethernet POS Ports tabs18-24 DLP-F326 View Asap STM-N PM ParametersClick the Performance Ethernet POS Ports Statistics tabs Click the Performance Optical tabs Figure18-25 DLP-F327 View Asap Ether Ports Statistics PM ParametersEther Ports Statistics in the Card View Performance Window 18-2618-27 DLP-F328 View Asap Ether Ports Utilization PM Parameters18-28 DLP-F329 View Asap POS Ports Statistics PM Parameters18-29 DLP-F330 View Asap POS Ports Utilization PM Parameters18-30 DLP-F331 View Asap POS Ports History PM Parameters18-31 DLP-F332 Change Node Access and PM Clearing Privilege18-32 18-33 DLP-F333 Install the Asap Carrier Modules18-34 DLP-F334 Verify Pass-Through Circuits18-35 DLP-F335 Preprovision an SFP18-36 DLP-F336 Print CTC Data18-37 DLP-F337 View Asap Ether Ports History PM Parameters18-38 Click the Provisioning MS-SPRing tabs Click Create MS-SPRing18-39 18-40 DLP-F339 Create a Two-Fiber MS-SPRing Manually18-41 DLP-F340 Change an MS-SPRing Node ID18-42 DLP-F341 MS-SPRing Exercise Ring Test18-43 DLP-F342 MS-SPRing Switch TestClick the Maintenance MS-SPRing tabs Click Retrieve18-44 18-45 18-46 DLP-F344 Initiate an MS-SPRing Manual Ring Switch DLP-F343 Provision an STM-N Circuit Route18-47 DLP-F345 Clear an MS-SPRing Manual Ring Switch Onsite/Remote Onsite Security Level Provisioning or higher18-48 18-49 DLP-F346 Create an MS-SPRing on a Single Node18-50 DLP-F347 Initiate an MS-SPRing Force Ring Switch18-51 DLP-F348 View Circuit InformationSncp 2F-PCADRI PCA18-53 Pendingmerge Droppending18-54 18-55 11 Connecting Fiber to a Four-Node, Two-Fiber MS-SPRing18-56 DLP-F350 Delete an MS-SPRing from a Single Node12 Selecting Single Roll Attributes 18-5714 Selecting a New Endpoint 18-5815 Viewing the Rolls Tab 18-5918-60 18-61 18-62 Click the Circuits tab17 Selecting Dual Roll Attributes 18-6318-64 18 Setting Roll Routing Preferences18-65 18-66 18-67 18-68 DLP-F356 Delete a Roll Click the Circuits Rolls tabs18-69 DLP-F357 Cancel a Roll DLP-F358 Provision a Multirate PPM18-70 DLP-F359 Change the Optical Line Rate Click the Provisioning Pluggable Port Modules tabs18-71 18-72 DLP-F360 Delete a PPM18-73 DLP-F361 Provision OSI Routing ModeNode view, click the Provisioning OSI Tarp Config tabs DLP-F362 Provision or Modify Tarp Operating Parameters18-74 18-75 Node view, click the Provisioning OSI Tarp Static TDC tabs Click Add Static Entry18-76 DLP-F365 Add a Tarp Manual Adjacency Table Entry Click Delete Static Entry18-77 Click the Provisioning OSI Routers Setup tabs DLP-F366 Provision OSI Routers18-78 DLP-F368 Enable the OSI Subnet on the LAN Interface DLP-F367 Provision Additional Manual Area Addresses18-79 DLP-F369 Create an IP-Over-CLNS Tunnel Click the Provisioning OSI Tunnels tabs18-80 18-81 DLP-F370 Remove a Tarp Manual Adjacency Table Entry18-82 DLP-F371 Change the OSI Routing Mode18-83 DLP-F372 Edit the OSI Router Configuration18-84 DLP-F373 Edit the OSI Subnetwork Point of AttachmentDLP-F374 Edit an IP-Over-CLNS Tunnel Node view, click the Provisioning OSI Routers Subnet tabs18-85 DLP-F375 Delete an IP-Over-CLNS Tunnel18-86 DLP-F376 View IS-IS Routing Information BaseDLP-F377 View ES-IS Routing Information Base DLP-F378 Manage the Tarp Data Cache18-87 18-88 DLP-F379 Export CTC Data19 Selecting CTC Data for Export 18-8918-90 DLP-F380 Configure the Node for Radius Authentication20 Radius Server Tab 18-91DLP-F381 Delete a Server Trail Click the Provisioning Server Trails tabs18-92 DLP-F383 Download an Alarm Severity Profile DLP-F382 Grant Superuser Privileges to a Provisioning User18-93 18-94 18-95 DLP-F384 Install the Asap 1PIO and 4PIO PIM Modules22 1PIO Module Faceplate 18-9618-97 DLP-F385 Consolidate Links in Network View18-98 24shows a network view with unconsolidated DCC and PPC linksALL Dwdm GCC, OTS, PPC TDM18-99 DLP-F386 Adjust the Java Virtual Memory Heap Size DLP-F387 Install an SFP/XFP18-100 18-101 DLP-F388 Remove an SFP/XFP18-102 DLP-F389 Remove a 1PIO or 4PIO PIM ModuleClick the Provisioning Optical Line tabs DLP-F390 Provision an Optical Line Rate and WavelengthAsap 4PIO 1PIODLP-F391 Install Alarm Wires on the CAP/CAP2 CAP/CAP218-104 27 Rear of the ONS 15600 SDH, Including the CAP/CAP2 18-10528 CAP/CAP2 Faceplate and Connections 18-10618-107 DLP-F392 Change Line Transmission Settings for STM-N CardsSF BER SD BER18-108 18-109 SonetSets STU18-110 18-111 DLP-F393 Change Threshold Settings for STM-N Ports18-112 18-113 DLP-F394 Change Optics Threshold Settings for STM-N Ports18-114 RefreshDLP-F395 Change the STM-N Port ALS Maintenance Settings Click the Maintenance ALS tabs18-115 18-116 DLP-F396 Clear All PM Thresholds18-117 DLP-F397 Provision the Designated Socks Servers18-118 18-119 18-120
Top Page Image Contents