Tripp Lite 220/230/240V Input/Output owner manual Basic Operation

Page 8

Basic Operation (continued)

Front Panel Indicator Lights continued

“BYPASS” LED: This yellow light will flash to indicate that the UPS’s DC/AC inverter is deactivated and the UPS is in the “Bypass” mode. During normal operation this LED will light briefly when the unit is plugged in, but if an internal fault or overload occurs this light will flash constantly to show that connected equipment will receive filtered AC mains power, but will not receive battery power during a blackout. In this case, contact Tripp Lite for service.

“FAULT” LED (select models only): This red light will flash when your UPS detects an internal fault (overheating, overvoltages, etc.). If the light persists after restarting the UPS, contact Tripp Lite for service.

“LOAD ACTIVE METER” LED: This green light will illuminate when your UPS is receiving AC power to indicate that the set of four dual-function LEDs is displaying the load level of your UPS.

“BATT ACTIVE METER” LED: This green light will illuminate when your UPS is operating from battery power to indicate that the set of four dual-function LEDs is displaying the battery charge level of your UPS. Note: the “ON BATT” LED will also be illuminated.

“OVERLOAD” LED: This red light will illuminate constantly to indicate that your UPS’s capacity has been exceeded while it is in on-line operation. The UPS alarm will beep continuously. Immediately remove overload until light and alarm go off. If you do not immediately remove the overload, the UPS will transfer from on-line to bypass operation.

“BATT LOW” LED: This yellow light will illuminate when your UPS’s battery charge level is low. The UPS alarm will beep until either the battery charge is depleted or the batteries are adequately recharged.

“ON BATT” LED: This green light will illuminate constantly to indicate that AC line voltage is not present and your UPS is providing your equipment with battery power. The UPS will also beep every two seconds, unless silenced by the “ON/TEST” Button. When this light is illuminated, you can monitor the battery charge level of your UPS on the “BATT ACTIVE METER” LEDs.

8

Image 8
Contents SmartOnline Th Street Chicago, IL 60609 USAImportant Safety Instructions UPS Location WarningsPost Mounting Mounting RackPost Telecom Mounting Mounting Tower Connection and Start-UpInstallationImporant Safety Instructions Turn the UPS onPhone/Network Line Suppression Optional ConnectionsEPO Port Connection External Battery ConnectionUSB and RS-232 Serial Communications Front Panel Switches Front Panel Indicator LightsBasic Operation Rear Panel Communications Restart the UPS. If the problem persists Or low for the UPS to operate in Bypass This indicates that utility power is too highAdequate space for air to circulate near Procedure Service StorageManual del usuario Th Street Chicago, IL 60609 EE.UUImportantes instrucciones de seguridad Guarde Estas InstruccionesMontaje de 4 postes Montaje de 2 postes Telecomunicaciones Conexión y encendidoEncienda el UPS Conexiones opcionalesConexión de Puerto USB y DB9 Conexión con un puerto EPOConexión del paquete de baterías externas Conexiones opcionales continuaciónInterruptores del panel frontal Luces indicadoras del panel frontalOperación básica continuación Luces indicadoras del panel frontal continuaciónPanel posterior Panel posterior continuación ComunicacionesEncendida FAULT, 100% Encendida FAULT, BYPASS, LINE, 50%Encendida FAULT, BYPASS, Line Encendida FAULT, BYPASS, LINE, 25%Localización de fallas continuación Modelos de UPS de 2U Reemplazo de bateríaProcedimiento Almacenamiento ServicioGuide de lutilisateur Th Street, Chicago, IL 60609 USAImportantes consignes de sécurité Conservez CES Instructions EN UN Lieu SÛRBâti à quatre montants Montage Tour Installation suiteMontage sur 2 montants Télécom Mettre en fonction londuleur Connexion et démarrageConnexions facultatives suite Connexion du port USB et du port série DB9Connexion du port darrêt durgence Commutateurs du panneau avant Voyants du panneau avantExploitation de base suite Voyants du panneau avant suitePanneau arrière Panneau arrière suite Communiquez avec le service à la Problème Remplacez la batterieON/Test comme décrit en Clientèle de Tripp LiteDépannage suite Procédure Entreposage EntretienPage Ðóêîâîäñòâî ïîëüçîâàòåëÿ Âàæíûå óêàçàíèÿ ïî òåõíèêå áåçîïàñíîñòè Ñîõðàíèòå ÝÒÓ ÈíñòðóêöèþÓñòàíîâêà ÈÁÏ Ìîíòàæíûå ñòîéêèÓñòàíîâêà ÈÁÏ ïðîäîëæåíèå Êðåïëåíèå íà ÷åòûðåõ ñòîéêàõ TelecomÂêëþ÷åíèå ÈÁÏ Ïîñëåäîâàòåëüíûå êîììóíèêà-öèîííûå ïîðòû USB è RS-232 Áàçîâûå èíñòðóêöèè ïî èñïîëüçîâàíèþ ÈÁÏ Êíîïêè íà ïåðåäíåé ïàíåëèÏðîäîëæåíèå Áàçîâûå èíñòðóêöèè ïî èñïîëüçîâàíèþ ÈÁÏ Çàäíÿÿ ïàíåëü ïðîäîëæåíèå Ïîèñê è óñòðàíåíèå íåèñïðàâíîñòåé Çàìåíèòå ÁàòàðåèÏîèñê è óñòðàíåíèå íåèñïðàâíîñòåé ïðîäîëæåíèå Çàìåíà àêêóìóëÿòîðíûõ áàòàðåé Õðàíåíèå è òåõîáñëóæèâàíèå