Tripp Lite 220/230/240V Input/Output Front Panel Switches, Front Panel Indicator Lights

Page 7

Basic Operation

Front Panel Switches

“ON/TEST” Button: This switch controls four separate UPS functions:

UPS Power ON

To turn the UPS on, press this button, hold it for several seconds until you hear a beep, then release it. The “ON LINE” LED will illuminate.

UPS Self-Test

During normal on-line operation, press this button and hold it until you hear a beep. This initiates a 10-second self-test of the battery. The UPS will shift to battery power (all LEDs will illuminate) for ten seconds.

Alarm Silence

To silence the UPS “on-battery” alarm, press this button and hold it until you hear a beep.

UPS Cold Start

To use your UPS as a stand-alone power source when AC power is unavailable (i.e. during a blackout), press this button and hold it until you hear a beep. The UPS will then provide battery power to its outlets.*

*The “ON BATT” Indicator Light will be illuminated since your UPS will be operating from battery power.

“OFF” Button: This button turns power OFF at the UPS receptacles. Press this switch, hold it until you hear a beep, then release it. The UPS will continue charging and the fan will continue to cool internal components even after you turn the UPS receptacles off. To turn the UPS OFF completely, including the charger, disconnect the UPS’s power cord after pressing the “OFF” switch.

Front Panel Indicator Lights

“ON LINE” LED: This green light will illuminate constantly to indicate the UPS is performing normal on-line operation (filtering and resynthesizing incoming AC line voltage to provide pure sine wave output). When this light is illuminated, you can monitor the load level of your UPS on the “LOAD ACTIVE METER” LEDs.

“LINE” LED: This green light will illuminate constantly to indicate the utility supplied AC line voltage at your wall outlet is nominal. It will flash if the line voltage is outside the nominal range (either too low or two high). No action is required on your part when the LED flashes; the UPS continuously and automatically filters AC line power to provide your equipment with pure sine wave AC power, regardless of brownout or overvoltage conditions. If this light is off, then AC line voltage is not present (blackout) or is at an extremely high voltage, and the UPS will provide connected equipment with power from battery.

7

Image 7
Contents Th Street Chicago, IL 60609 USA SmartOnlineUPS Location Warnings Important Safety InstructionsMounting Rack Post MountingConnection and Start-Up Post Telecom Mounting Mounting TowerOptional Connections InstallationImporant Safety InstructionsTurn the UPS on Phone/Network Line SuppressionUSB and RS-232 Serial Communications External Battery ConnectionEPO Port Connection Front Panel Indicator Lights Front Panel SwitchesBasic Operation Rear Panel Communications Restart the UPS. If the problem persists Adequate space for air to circulate near This indicates that utility power is too highOr low for the UPS to operate in Bypass Procedure Storage ServiceTh Street Chicago, IL 60609 EE.UU Manual del usuarioGuarde Estas Instrucciones Importantes instrucciones de seguridadMontaje de 4 postes Conexión y encendido Montaje de 2 postes TelecomunicacionesConexiones opcionales Encienda el UPSConexiones opcionales continuación Conexión de Puerto USB y DB9Conexión con un puerto EPO Conexión del paquete de baterías externasLuces indicadoras del panel frontal Interruptores del panel frontalLuces indicadoras del panel frontal continuación Operación básica continuaciónPanel posterior Comunicaciones Panel posterior continuaciónEncendida FAULT, BYPASS, LINE, 25% Encendida FAULT, 100%Encendida FAULT, BYPASS, LINE, 50% Encendida FAULT, BYPASS, LineLocalización de fallas continuación Procedimiento Reemplazo de bateríaModelos de UPS de 2U Servicio AlmacenamientoTh Street, Chicago, IL 60609 USA Guide de lutilisateurConservez CES Instructions EN UN Lieu SÛR Importantes consignes de sécuritéBâti à quatre montants Montage sur 2 montants Télécom Installation suiteMontage Tour Connexion et démarrage Mettre en fonction londuleurConnexion du port darrêt durgence Connexion du port USB et du port série DB9Connexions facultatives suite Voyants du panneau avant Commutateurs du panneau avantVoyants du panneau avant suite Exploitation de base suitePanneau arrière Panneau arrière suite Clientèle de Tripp Lite Communiquez avec le service à laProblème Remplacez la batterie ON/Test comme décrit enDépannage suite Procédure Entretien EntreposagePage Ðóêîâîäñòâî ïîëüçîâàòåëÿ Ñîõðàíèòå ÝÒÓ Èíñòðóêöèþ Âàæíûå óêàçàíèÿ ïî òåõíèêå áåçîïàñíîñòèÌîíòàæíûå ñòîéêè Óñòàíîâêà ÈÁÏÊðåïëåíèå íà ÷åòûðåõ ñòîéêàõ Telecom Óñòàíîâêà ÈÁÏ ïðîäîëæåíèåÂêëþ÷åíèå ÈÁÏ Ïîñëåäîâàòåëüíûå êîììóíèêà-öèîííûå ïîðòû USB è RS-232 Êíîïêè íà ïåðåäíåé ïàíåëè Áàçîâûå èíñòðóêöèè ïî èñïîëüçîâàíèþ ÈÁÏÏðîäîëæåíèå Áàçîâûå èíñòðóêöèè ïî èñïîëüçîâàíèþ ÈÁÏ Çàäíÿÿ ïàíåëü ïðîäîëæåíèå Çàìåíèòå Áàòàðåè Ïîèñê è óñòðàíåíèå íåèñïðàâíîñòåéÏîèñê è óñòðàíåíèå íåèñïðàâíîñòåé ïðîäîëæåíèå Õðàíåíèå è òåõîáñëóæèâàíèå Çàìåíà àêêóìóëÿòîðíûõ áàòàðåé