Q-Logic 2300 series manual QCP2330/2332 HBA Components, LEDs

Page 11

Section 2

QCP2330/2332

2.1

QCP2330/2332 HBA Components

Figure 2-1identifies the QCP2330/2332 HBA components referenced throughout this section.

Each QCP2330/2332 HBA has a unique serial number, located on the back of the HBA. Take a minute to write down the serial number of the QCP2330/2332 HBA in the unlikely event that the NVRAM is corrupted.

J1

1

3 J5

J6

J2

1

3

J5 and J1 QCP2332

ONLY

ISP CHIP

ISP CHIP

QCP2332

ONLY

LED1

RELEASE SWITCH

NOTE: THE SERIAL NUMBER IS ON THE OTHER SIDE

OF THE HBA.

Figure 2-1. QCP2330/2332 HBA Layout

2.1.1

LEDs

In a standard installation, LED1 is off, indicating that the HBA is active.

In a hot swap installation, LED1 turns blue while the HBA is inserted. If the LED turns off, the HBA is inserted and has been configured.

CF2351102-00 F

2-1

Image 11

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page General Description How to Use this GuideWhat is Fibre Channel? IntroductionCompliance with the following PCI standards QCP HBAs FeaturesHardware Hardware CF2351102-00 F LEDs QCP2330/2332QCP2330/2332 HBA Components Jumpers Installation and RemovalInstallation in the Computer Standard ApId Type Receptacle Occupant Condition Installation in the Computer Hot SwapSystem configuration is as follows FCode Removing the QCP2330/2332 HBAUpdating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Connection ModeConnection mode and options display. For example Loop ID displays. For example Setting the QCP2330/2332 HBA Loop IDSelecting the Boot Device New connection mode displays. For exampleFollowing displays Building the Bootable DiskQCP2330/2332 FCode Install the boot block on the new boot disk. For example Use the rm command to delete the restoresymtable fileShut down the system. Type the following Setting and Viewing the Fibre Channel Data RateBoot from the newly created boot disk. For example View the current dump device setting. For exampleTables 2-2and 2-3define the QCP2330/2332 specifications SpecificationsConducted Emission LabelAgency Certification EMC/EMI Test RequirementsProduct Safety Requirements QCP2340/2342 HBA Components QCP2340/2342LED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Updating FCode on the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection ModeSetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following QCP2340/2342 Board Operating Environment Tables 3-3and 3-4define the QCP2340/2342 specificationsDMA EMI and EMC RequirementsEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 HBA Components QSB2340/2342Installation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Loop ID Setting the QSB2340/2342 HBA Connection ModeFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Shutdown the system. Type the following Tables 4-2and 4-3define the QSB2340/2342 specificationsClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Fibre Channel Problem Checklist TroubleshootingProblems After Installation Hardware Problem ChecklistPage Software II Software II-2 CF2351102-00 F Introduction Solaris Sparc Driver InstallationPre-installation Requirements Continue with in section Installing the Solaris Sparc Driver from a CD-ROMPress Enter to continue You are prompted to select a driver package. For exampleInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F