Q-Logic 2300 series manual ApId Type Receptacle Occupant Condition

Page 28

3 – QCP2340/2342 Installation and Removal

Q

A list of the system’s processors, memory, and I/O boats appears, as in the following example. In this example, cPCI slots 0, 1, 3, and 4 are available.

Ap_Id	Type	Receptacle	Occupant	Condition
N0.IB6	cPCI_I/O_bo	connected	configured	ok
N0.IB8	unknown	empty	unconfigured	unknown
N0.SB0	CPU_Board	connected	configured	ok
N0.SB2	CPU_Board	connected	configured	ok
c0	scsi-bus	connected	configured	unknown
pcisch0:sg6slot2	stpcipci/fhs	connected	configured	ok
			unconfigured
pcisch0:sg6slot3	unknown	empty	unconfigured	unknown
pcisc1:sg6slot0	unknown	empty	unconfigured	unknown
pcisch2:sg6slot4	unknown	empty	unconfigured	unknown
			unconfigured
pcisch2:sg6slot5	unknown	connected	unconfigured	unknown
			unconfigured
pcisch3:sg6slot1	unknown	empty	unconfigured	unknown

NOTE: If the cPCI slots are not displayed, add the following line to the etc/system file:

set sghsc:cpci_enable=1

Check the indicator lights next to the available slots (in some systems, the lights are above the slots). The top two lights are off; the bottom light is amber. This is another way to verify an available slot.

3.Place the QCP2340/2342 HBA into the slot. Carefully press the HBA into the slot until it seats firmly (the switch clicks into a locked position when the HBA is seated). The bottom indicator light next to (or above) the slot changes from amber to off. The top indicator light turns green.

The hot swap LED3 on the QCP2340/2342 HBA turns blue while the HBA is inserted. If LED3 turns off, the HBA is inserted and has been configured; continue with step 6. If LED3 stays blue after the HBA is inserted, continue with step 4.

3-4	CF2351102-00 F

Image 28

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page How to Use this Guide What is Fibre Channel?Introduction General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F QCP2330/2332 HBA Components QCP2330/2332LEDs Installation in the Computer Standard Installation and RemovalJumpers Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeConnection mode and options display. For example Setting the QCP2330/2332 HBA Connection ModeUpdating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Loop ID Selecting the Boot DeviceNew connection mode displays. For example Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleSetting and Viewing the Fibre Channel Data Rate Boot from the newly created boot disk. For exampleView the current dump device setting. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsLabel Agency CertificationEMC/EMI Test Requirements Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Troubleshooting Problems After InstallationHardware Problem Checklist Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Pre-installation Requirements Solaris Sparc Driver InstallationIntroduction Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F