Q-Logic 2300 series manual System configuration is as follows

Page 14

2 – QCP2330/2332 Installation and Removal

Q

4.Type the cfgadm command (see step 2) to verify that the system recognizes the QCP2330/2332 HBA and that the HBA is not configured. In the following example, the QCP2330/2332 HBA has been installed in slot 4 and is not configured.

Ap_Id	Type	Receptacle	Occupant	Condition
N0.IB6	cPCI_I/O_bo	connected	configured	ok
N0.IB8	unknown	empty	unconfigured	unknown
N0.SB0	CPU_Board	connected	configured	ok
N0.SB2	CPU_Board	connected	configured	ok
c0	scsi-bus	connected	configured	unknown
pcisch0:sg6slot2	stpcipci/fhs	connected	configured	ok
pcisch0:sg6slot3	unknown	empty	unconfigured	unknown
pcisc1:sg6slot0	unknown	empty	unconfigured	unknown
			unconfigured
pcisch2:sg6slot4	unknown	disconnected	unconfigured	unknown
			unconfigured
pcisch2:sg6slot5	unknown	connected	unconfigured	unknown
pcisch3:sg6slot1	unknown	empty	unconfigured	unknown

5. Type the following commands to configure the QCP2330/2332 HBA:

cfgadm -c configure slot path

For example, type the following commands to configure the QCP2330/2332 HBA in slot 4, as shown in step 4:

cfgadm -c configure pcisch2:sg6slot4

The system configuration is as follows:

Ap_Id	Type	Receptacle	Occupant	Condition
N0.IB6	cPCI_I/O_bo	connected	configured	ok
N0.IB8	unknown	empty	unconfigured	unknown
N0.SB0	CPU_Board	connected	configured	ok
N0.SB2	CPU_Board	connected	configured	ok
c0	scsi-bus	connected	configured	unknown
pcisch0:sg6slot2	stpcipci/fhs	connected	configured	ok
pcisch0:sg6slot3	unknown	empty	unconfigured	unknown
pcisc1:sg6slot0	unknown	empty	unconfigured	unknown
			configured
pcisch2:sg6slot4	stpcipci/fhs	connected	configured	ok
			unconfigured
pcisch2:sg6slot5	unknown	connected	unconfigured	unknown
pcisch3:sg6slot1	unknown	empty	unconfigured	unknown

2-4	CF2351102-00 F

Image 14

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page Introduction How to Use this GuideWhat is Fibre Channel? General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F LEDs QCP2330/2332QCP2330/2332 HBA Components Jumpers Installation and RemovalInstallation in the Computer Standard Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeUpdating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Connection ModeConnection mode and options display. For example New connection mode displays. For example Setting the QCP2330/2332 HBA Loop IDSelecting the Boot Device Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleView the current dump device setting. For example Setting and Viewing the Fibre Channel Data RateBoot from the newly created boot disk. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsEMC/EMI Test Requirements LabelAgency Certification Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Hardware Problem Checklist TroubleshootingProblems After Installation Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Introduction Solaris Sparc Driver InstallationPre-installation Requirements Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F