Q-Logic 2300 series manual LEDs, Installation in the Computer

Page 42

4 – QSB2340/2342 Installation in the Computer

Q

4.1.1

LEDs

The QSB2340/2342 LED1 and LED2 (QSB2342) function as shown in table 4-1.

Table 4-1. LED1 and LED2 (QCP2342) Activity

Green LED	Amber LED	Activity

On	On	Power
On	Off	Online
Off	On	Signal acquired
Off	Flashing	Loss of synchronization
Flashing	Flashing	Firmware error

4.1.2

Jumpers

Jumpers J7 (QSB2342) and J8 on the QSB2340/2342 HBA determine the default state of connectors J10 (QSB2342) and J9, respectively. The jumpers are set at the factory with a jumper plug on pins 2–3, which enables the connectors.

CAUTION! Changing the jumper settings can result in the HBA being inoperable.

4.2

Installation in the Computer

Before you install the QSB2340/2342 HBA in your computer, you need the following:

■A screwdriver (usually a Phillips #1)

■An optical, multimode cable with an LC-style duplex connector

Perform the following steps to install the QSB2340/2342 HBA in your system:

1.Shut down the computer.

2.Remove the computer cover and save the screws.

3.Choose any available SBus slot.

4.Remove the slot cover.

5.Place the QSB2340/2342 HBA into the slot. Carefully press the HBA into the slot until it seats firmly.

6.Connect the appropriate cable from the devices to the J1 and J2 connectors.

7.Carefully reinstall the computer cover. Insert and tighten the computer cover screws.

8.Power up all external FC devices, then power up the system and observe the monitor.

NOTE: SunSPARC systems do not display the BIOS banner.

4-2	CF2351102-00 F

Image 42

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page Introduction How to Use this GuideWhat is Fibre Channel? General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F QCP2330/2332 QCP2330/2332 HBA ComponentsLEDs Installation and Removal Installation in the Computer StandardJumpers Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeSetting the QCP2330/2332 HBA Connection Mode Connection mode and options display. For exampleUpdating FCode on the QCP2330/2332 HBA New connection mode displays. For example Setting the QCP2330/2332 HBA Loop IDSelecting the Boot Device Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleView the current dump device setting. For example Setting and Viewing the Fibre Channel Data RateBoot from the newly created boot disk. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsEMC/EMI Test Requirements LabelAgency Certification Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Hardware Problem Checklist TroubleshootingProblems After Installation Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Solaris Sparc Driver Installation Pre-installation RequirementsIntroduction Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F