Q-Logic 2300 series manual Installation in the Computer Hot Swap

Page 13

Q

2 – QCP2330/2332 Installation and Removal

2.2.2

Installation in the Computer (Hot Swap)

Perform the following steps to install the QCP2330/2332 HBA without shutting down the system (hot swap). See section 2.2.1 for standard installation instructions.

1.Log on to the system as a superuser.

2.At the prompt (#), type the following command to find an available slot for the QCP2330/2332 HBA:

cfgadm

A list of the system’s processors, memory, and I/O boats appears, as in the following example. In this example, cPCI slots 0, 1, 3, and 4 are available.

Ap_Id	Type	Receptacle	Occupant	Condition
N0.IB6	cPCI_I/O_bo	connected	configured	ok
N0.IB8	unknown	empty	unconfigured	unknown
N0.SB0	CPU_Board	connected	configured	ok
N0.SB2	CPU_Board	connected	configured	ok
c0	scsi-bus	connected	configured	unknown
pcisch0:sg6slot2	stpcipci/fhs	connected	configured	ok
			unconfigured
pcisch0:sg6slot3	unknown	empty	unconfigured	unknown
pcisc1:sg6slot0	unknown	empty	unconfigured	unknown
pcisch2:sg6slot4	unknown	empty	unconfigured	unknown
			unconfigured
pcisch2:sg6slot5	unknown	connected	unconfigured	unknown
			unconfigured
pcisch3:sg6slot1	unknown	empty	unconfigured	unknown

NOTE: If the cPCI slots are not displayed, add the following line to the etc/system file:

set sghsc:cpci_enable=1

Check the indicator lights next to the available slots (in some systems, the lights are above the slots). The top two lights are off; the bottom light is amber. This is another way to verify an available slot.

3.Place the QCP2330/2332 HBA into the slot. Carefully press the HBA into the slot until it seats firmly (the switch clicks into a locked position when the HBA is seated). The bottom indicator light next to (or above) the slot changes from amber to off. The top indicator light turns green.

The hot swap LED1 on the QCP2330/2332 HBA turns blue while the HBA is inserted. If LED1 turns off, the HBA is inserted and has been configured; continue with step 6. If LED1 stays blue after the HBA is inserted, continue with step 4.

CF2351102-00 F

2-3

Image 13

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page What is Fibre Channel? How to Use this GuideIntroduction General DescriptionCompliance with the following PCI standards QCP HBAs FeaturesHardware Hardware CF2351102-00 F QCP2330/2332 HBA Components QCP2330/2332LEDs Installation in the Computer Standard Installation and RemovalJumpers ApId Type Receptacle Occupant Condition Installation in the Computer Hot SwapSystem configuration is as follows FCode Removing the QCP2330/2332 HBAConnection mode and options display. For example Setting the QCP2330/2332 HBA Connection ModeUpdating FCode on the QCP2330/2332 HBA Selecting the Boot Device Setting the QCP2330/2332 HBA Loop IDNew connection mode displays. For example Loop ID displays. For exampleFollowing displays Building the Bootable DiskQCP2330/2332 FCode Install the boot block on the new boot disk. For example Use the rm command to delete the restoresymtable fileBoot from the newly created boot disk. For example Setting and Viewing the Fibre Channel Data RateView the current dump device setting. For example Shut down the system. Type the followingTables 2-2and 2-3define the QCP2330/2332 specifications SpecificationsAgency Certification LabelEMC/EMI Test Requirements Conducted EmissionProduct Safety Requirements QCP2340/2342 HBA Components QCP2340/2342LED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Updating FCode on the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection ModeSetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following QCP2340/2342 Board Operating Environment Tables 3-3and 3-4define the QCP2340/2342 specificationsDMA EMI and EMC RequirementsEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 HBA Components QSB2340/2342Installation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Loop ID Setting the QSB2340/2342 HBA Connection ModeFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Shutdown the system. Type the following Tables 4-2and 4-3define the QSB2340/2342 specificationsClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Problems After Installation TroubleshootingHardware Problem Checklist Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Pre-installation Requirements Solaris Sparc Driver InstallationIntroduction Continue with in section Installing the Solaris Sparc Driver from a CD-ROMPress Enter to continue You are prompted to select a driver package. For exampleInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F