Q-Logic 2300 series manual QCP2340/2342 HBA Components

Page 25

Section 3

QCP2340/2342

3.1

QCP2340/2342 HBA Components

Figure 3-1identifies the QCP2340/2342 HBA components referenced throughout this section.

Each QCP2340/2342 HBA has a unique serial number, located on the back of the HBA. Take a minute to write down the serial number of the QCP2340/2342 HBA in the unlikely event that the NVRAM is corrupted.

J5

1

3

LED1 J1 PORT 1

J2 PORT 2

	J4
LED2	1
LED2	3

J2, J4, and LED2 QCP2342 ONLY

ISP CHIP

LED3

RELEASE SWITCH

NOTE: THE SERIAL NUMBER IS ON THE OTHER SIDE OF THE HBA.

Figure 3-1. QCP2340/2342 HBA Layout

CF2351102-00 F

3-1

Image 25

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page What is Fibre Channel? How to Use this GuideIntroduction General DescriptionCompliance with the following PCI standards QCP HBAs FeaturesHardware Hardware CF2351102-00 F QCP2330/2332 HBA Components QCP2330/2332LEDs Installation in the Computer Standard Installation and RemovalJumpers ApId Type Receptacle Occupant Condition Installation in the Computer Hot SwapSystem configuration is as follows FCode Removing the QCP2330/2332 HBAConnection mode and options display. For example Setting the QCP2330/2332 HBA Connection ModeUpdating FCode on the QCP2330/2332 HBA Selecting the Boot Device Setting the QCP2330/2332 HBA Loop IDNew connection mode displays. For example Loop ID displays. For exampleFollowing displays Building the Bootable DiskQCP2330/2332 FCode Install the boot block on the new boot disk. For example Use the rm command to delete the restoresymtable fileBoot from the newly created boot disk. For example Setting and Viewing the Fibre Channel Data RateView the current dump device setting. For example Shut down the system. Type the followingTables 2-2and 2-3define the QCP2330/2332 specifications SpecificationsAgency Certification LabelEMC/EMI Test Requirements Conducted EmissionProduct Safety Requirements QCP2340/2342 HBA Components QCP2340/2342LED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Updating FCode on the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection ModeSetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following QCP2340/2342 Board Operating Environment Tables 3-3and 3-4define the QCP2340/2342 specificationsDMA EMI and EMC RequirementsEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 HBA Components QSB2340/2342Installation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Loop ID Setting the QSB2340/2342 HBA Connection ModeFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Shutdown the system. Type the following Tables 4-2and 4-3define the QSB2340/2342 specificationsClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Problems After Installation TroubleshootingHardware Problem Checklist Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Pre-installation Requirements Solaris Sparc Driver InstallationIntroduction Continue with in section Installing the Solaris Sparc Driver from a CD-ROMPress Enter to continue You are prompted to select a driver package. For exampleInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F