Q-Logic 2300 series manual Building the Bootable Disk

Page 46

4 – QSB2340/2342 FCode

Q

5.Save the boot device information to the QSB2340/2342 HBA’s NVRAM. Use the set-boot-idcommand. Include the selected QSB2340/2342 HBA’s WWN, loop ID, and LUN. For example:

ok 2200002037009eeb 82 0 set-boot-id

The following displays:

Calculating NVRAM checksum, please wait.... done

Boot device login successful

Boot WWN - 20000020 37009eeb WWPN - 22000020 37009eeb Id - 82 Lun - 0

ok

To boot the QSB2340/2342 HBA, type the complete boot path, including the loop ID and LUN. The loop ID and LUN must match those entered in step 5. For example:

ok boot /sbus@1f,0/QLGC,qla@1,30000/sd@82,0

NOTE: Enter the reset command before attempting to boot if the boot was interrupted or any of the QLogic FCode commands were executed.

4.3.5

Building the Bootable Disk

This procedure assumes that the system is already booted from an existing system disk, and that you have already performed a full system backup.

The device path on each system differs, depending on the SBus slot, target ID, LUN, etc. The device name shown in this example is for a device on the third SBus slot, target ID 130, LUN 0, slice 0.

You must have already completed the steps in the previous sections before attempting to create a bootable disk.

This procedure involves using the Solaris ufsdump command to create temporary saveset files for each partition on your current boot disk. For this method to be successful, you must have enough extra disk space to create the saveset files, or your Solaris machine must have a high-capacity tape drive attached.

4-6	CF2351102-00 F

Image 46

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page Introduction How to Use this GuideWhat is Fibre Channel? General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F QCP2330/2332 HBA Components QCP2330/2332LEDs Installation in the Computer Standard Installation and RemovalJumpers Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeConnection mode and options display. For example Setting the QCP2330/2332 HBA Connection ModeUpdating FCode on the QCP2330/2332 HBA New connection mode displays. For example Setting the QCP2330/2332 HBA Loop IDSelecting the Boot Device Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleView the current dump device setting. For example Setting and Viewing the Fibre Channel Data RateBoot from the newly created boot disk. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsEMC/EMI Test Requirements LabelAgency Certification Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Hardware Problem Checklist TroubleshootingProblems After Installation Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Pre-installation Requirements Solaris Sparc Driver InstallationIntroduction Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F