Q-Logic 2300 series manual Shut down the system. Type the following

Page 36

3 – QCP2340/2342 FCode

Q

9.Edit the new vfstab file to properly mount the new partitions during boot. In this case, each reference to c0t0d0s0 is changed to c3t130d0s0. For example:

vi/mnt/etc/vfstab

10.Shut down the system. Type the following:

/sbin/init 0

11. Boot from the newly created boot disk. For example:

boot /pci@1f,0/pci@1/QLGC,qla@4/sd@82,0

NOTE: The target device ID (sd@82) is in hexadecimal. The decimal value is used in step 3.

12. View the current dump device setting. For example:

# dumpadm

Dump content: kernel pages

Dump device: /dev/dsk/c0t0d0s1 (swap)

Savecore directory: /var/crash/saturn

Savecore enabled: yes

13. Change the dump device to the swap area of the new boot drive. For example:

# dumpadm -d /dev/dsk/c3t130d0s1

NOTE: Steps 14 and 15 set the newly created boot disk as the default boot disk. These steps are performed at the system OBP (ok) prompt.

14. Create an alias entry for the new boot device (optional). For example:

ok nvalias fibredisk /pci@1f,0/pci@1/QLGC,qla@4/sd@82,0

15.Set default boot device to be the new boot device (optional). For example: ok setenv boot-disk fibredisk

3-12	CF2351102-00 F

Image 36

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page How to Use this Guide What is Fibre Channel?Introduction General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F QCP2330/2332 QCP2330/2332 HBA ComponentsLEDs Installation and Removal Installation in the Computer StandardJumpers Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeSetting the QCP2330/2332 HBA Connection Mode Connection mode and options display. For exampleUpdating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Loop ID Selecting the Boot DeviceNew connection mode displays. For example Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleSetting and Viewing the Fibre Channel Data Rate Boot from the newly created boot disk. For exampleView the current dump device setting. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsLabel Agency CertificationEMC/EMI Test Requirements Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Troubleshooting Problems After InstallationHardware Problem Checklist Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Solaris Sparc Driver Installation Pre-installation RequirementsIntroduction Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F