Q-Logic 2300 series manual Class B

Page 50

4 – QSB2340/2342 Label

Q

Table 4-3. QSB2340/2342 Board Specifications (Continued)

Type

Specification

 

 

Form factor

14.7cm8.4cm (5.8"8.4")

Operating

Less than 15 watts

power

 

 

 

4.5

Label

The transceiver on the QSB2340/2342 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated under recommended operating conditions.

CLASS I LASER PRODUCT

4.6

Agency Certification

The following sections contain a summary of the EMC/EMI test specifications performed on the QSB2340/2342 (SF0310401) to comply with radiated emission, radiated immunity, and product safety standards.

4.6.1

EMI and EMC Requirements

The QSB2340/2342 conforms to the following requirements:

FCC Part 15, Class B

Radiated Emission

Class B

Conducted Emission

Class B

ICES-003 Class B, Industry Canada

89/336/EEC EMC Directive CE

EN55022:1995 CISPR 22:1997 Class B

Radiated Emission

Class B

Conducted Emission

Class B

EN55024:1998

Immunity Standards

EN61000-4-2 :1995 ESD

EN61000-4-3 :1995 RF Electro Magnetic Field

EN61000-4-4 :1995 Fast Transient/Burst

4-10

CF2351102-00 F

Image 50
Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page Introduction How to Use this GuideWhat is Fibre Channel? General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F LEDs QCP2330/2332QCP2330/2332 HBA Components Jumpers Installation and RemovalInstallation in the Computer Standard Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeUpdating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Connection ModeConnection mode and options display. For example New connection mode displays. For example Setting the QCP2330/2332 HBA Loop IDSelecting the Boot Device Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleView the current dump device setting. For example Setting and Viewing the Fibre Channel Data RateBoot from the newly created boot disk. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsEMC/EMI Test Requirements LabelAgency Certification Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Hardware Problem Checklist TroubleshootingProblems After Installation Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Introduction Solaris Sparc Driver InstallationPre-installation Requirements Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F