Q-Logic 2300 series manual LED1 and LED2 QCP2342 Activity

Page 26

3 – QCP2340/2342 Installation and Removal

Q

3.1.1

LEDs

The QCP2340/2342 LED1 and LED2 (QCP2342) function as shown in table 3-1.

Table 3-1. LED1 and LED2 (QCP2342) Activity

Green LED	Amber LED	Activity

On	On	Power
On	Off	Online
Off	On	Signal acquired
Off	Flashing	Loss of synchronization
Flashing	Flashing	Firmware error

In a standard installation, LED3 is off, indicating that the HBA is active. In a hot swap installation, LED3 turns blue while the HBA is inserted. If the LED turns off, the HBA is inserted and has been configured.

3.1.2

Jumpers

Jumpers J4 (QCP2342) and J5 on the QCP2340/2322 HBA determine the default state of connectors J2 (QCP2342) and J1, respectively. The jumpers are set at the factory with a jumper plug on pins 2–3, which enables the connectors.

CAUTION! Changing the jumper settings can result in the HBA being inoperable.

3.2

Installation and Removal

The following sections describe how to install the QCP2340/2342 HBA (standard and hot swap installations) as well as how to remove the HBA.

Before you install the QCP2340/2342 HBA in your computer, you need the following:

■A screwdriver (usually a Phillips #1)

■An optical, multimode cable with an LC-style duplex connector

3.2.1

Installation in the Computer (Standard)

Perform the following steps to install the QCP2340/2342 HBA in your system. These instructions are for a standard installation (the computer is shut down). See section 3.2.2 for hot swap instructions.

1.Shut down the system.

2.Choose any available cPCI slot. (Check the indicator lights next to (or above) the available slots. The top two lights are off; the bottom light is amber.)

3-2	CF2351102-00 F

Image 26

Contents SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page Introduction How to Use this GuideWhat is Fibre Channel? General DescriptionFeatures Compliance with the following PCI standards QCP HBAsHardware Hardware CF2351102-00 F LEDs QCP2330/2332QCP2330/2332 HBA Components Jumpers Installation and RemovalInstallation in the Computer Standard Installation in the Computer Hot Swap ApId Type Receptacle Occupant ConditionSystem configuration is as follows Removing the QCP2330/2332 HBA FCodeUpdating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Connection ModeConnection mode and options display. For example New connection mode displays. For example Setting the QCP2330/2332 HBA Loop IDSelecting the Boot Device Loop ID displays. For exampleBuilding the Bootable Disk Following displaysQCP2330/2332 FCode Use the rm command to delete the restoresymtable file Install the boot block on the new boot disk. For exampleView the current dump device setting. For example Setting and Viewing the Fibre Channel Data RateBoot from the newly created boot disk. For example Shut down the system. Type the followingSpecifications Tables 2-2and 2-3define the QCP2330/2332 specificationsEMC/EMI Test Requirements LabelAgency Certification Conducted EmissionProduct Safety Requirements QCP2340/2342 QCP2340/2342 HBA ComponentsLED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Updating FCode on the QCP2340/2342 HBASetting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following Tables 3-3and 3-4define the QCP2340/2342 specifications QCP2340/2342 Board Operating EnvironmentEMI and EMC Requirements DMAEN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 QSB2340/2342 HBA ComponentsInstallation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Connection Mode Setting the QSB2340/2342 HBA Loop IDFor example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Tables 4-2and 4-3define the QSB2340/2342 specifications Shutdown the system. Type the followingClass B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Hardware Problem Checklist TroubleshootingProblems After Installation Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Introduction Solaris Sparc Driver InstallationPre-installation Requirements Installing the Solaris Sparc Driver from a CD-ROM Continue with in sectionYou are prompted to select a driver package. For example Press Enter to continueInstalling QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F