Ampro Corporation 700 manual PC/104 Interface J13 A/B, J14 C/D, Pin # Signal Description J13 Row a

Chapter 3 Hardware

PC/104 Interface (J13 A/B, J14 C/D)

The PC/104 Bus uses a 104-pin 0.10” header interface. This interface header will carry all of the appropriate PC/104 signals operating at clock speeds up to 8MHz. This interface header accepts stackable modules and is located on the top of the board.

Table 3-5. PC/104 Interface Pin/Signal Descriptions (J13A)

Pin #	Signal	Description (J13 Row A)
1 (A1)	IOCHCHK*	I/O Channel Check – This signal may be activated by ISA boards to
		request that a non-maskable interrupt (NMI) be generated to the system
		processor. It is driven active to indicate an uncorrectable error has been
		detected.
2 (A2)	SD7	System Data 7 – This signal (0 to 19) provides a system data bit.
3 (A3)	SD6	System Data 6 – Refer to SD7, pin-A2, for more information.
4 (A4)	SD5	System Data 5 – Refer to SD7, pin-A2, for more information.
5 (A5)	SD4	System Data 4 – Refer to SD7, pin-A2, for more information.
6 (A6)	SD3	System Data 3 – Refer to SD7, pin-A2, for more information.
7 (A7)	SD2	System Data 2 – Refer to SD7, pin-A2, for more information.
8 (A8)	SD1	System Data 1 – Refer to SD7, pin-A2, for more information.
9 (A9)	SD0	System Data 0 – Refer to SD7, pin-A2, for more information.
10 (A10)	IOCHRDY	I/O Channel Ready – This signal allows slower ISA boards to lengthen
		I/O or memory cycles by inserting wait states. This signal’s normal
		state is active high (ready). ISA boards drive the signal inactive low
		(not ready) to insert wait states. Devices using this signal to insert wait
		states should drive it low immediately after detecting a valid address
		decode and an active read, or write command. The signal is released
		high when the device is ready to complete the cycle.
11 (A11)	AEN	Address Enable – This signal is used to degate the system processor and
		other devices from the bus during DMA transfers. When this signal is
		active, the system DMA controller has control of the address, data, and
		read/write signals. This signal should be included as part of ISA board
		select decodes to prevent incorrect board selects during DMA cycles.
12 (A12)	SA19	System Address 19 – This signal (0 to 19) provides a system address bit.
13 (A13)	SA18	System Address 18 – Refer to SA19, pin-A12, for more information.
14 (A14)	SA17	System Address 17 – Refer to SA19, pin-A12, for more information.
15 (A15)	SA16	System Address 16 – Refer to SA19, pin-A12, for more information.
16 (A16)	SA15	System Address 15 – Refer to SA19, pin-A12, for more information.
17 (A17)	SA14	System Address 14 – Refer to SA19, pin-A12, for more information.
18 (A18)	SA13	System Address 13 – Refer to SA19, pin-A12, for more information.
19 (A19)	SA12	System Address 12– Refer to SA19, pin-A12, for more information.
20 (A20)	SA11	System Address 11 – Refer to SA19, pin-A12, for more information.
21 (A21)	SA10	System Address 10 – Refer to SA19, pin-A12, for more information.
22 (A22)	SA9	System Address 9 – Refer to SA19, pin-A12, for more information.
23 (A23)	SA8	System Address 8 – Refer to SA19, pin-A12, for more information.
24 (A24)	SA7	System Address 7 – Refer to SA19, pin-A12, for more information.

28 Reference Manual ReadyBoard 700