Ampro Corporation 700 manual Pin # Signal Descriptions J13 Row B

Chapter 3			Hardware
	Pin #	Signal	Description (J13 Row A)
	25 (A25)	SA6	System Address 6 – Refer to SA19, pin-A12, for more information.
	26 (A26)	SA5	System Address 5 – Refer to SA19, pin-A12, for more information.
	27 (A27)	SA4	System Address 4 – Refer to SA19, pin-A12, for more information.
	28 (A28)	SA3	System Address 3 – Refer to SA19, pin-A12, for more information.
	29 (A29)	SA2	System Address 2 – Refer to SA19, pin-A12, for more information.
	30 (A30)	SA1	System Address 1 – Refer to SA19, pin-A12, for more information.
	31 (A31)	SA0	System Address 0 – Refer to SA19, pin-A12, for more information.
	32 (A32)	GND	Ground

Notes: The shaded area denotes power or ground. The signals marked with * = Negative true logic.

Table 3-6. PC/104 Interface Pin/Signal Descriptions (J13B)

Pin #		Signal	Descriptions (J13 Row B)
33	(B1)	GND	Ground
34	(B2)	RESETDRV	Reset Drive – This signal is used to reset or initialize system logic on
			power up or subsequent system reset.
35	(B3)	+5V	+5 volt power ±10%
36	(B4)	IRQ9	Interrupt request 9 – Asserted by a device when it has pending interrupt
			request. Only one device may use the request line at a time.
37	(B5)	-5V	Not connected (-5 volts)
38	(B6)	DRQ2	DMA Request 2 – Used by I/O resources to request DMA service, or to
			request ownership of the bus as a bus master device. Must be held high
			until associated DACK2 line is active.
39	(B7)	-12V	Not connected (-12 volts)
40	(B8)	ENDXFR*	Zero Wait State – This signal is driven low by a bus slave device to
			indicate it is capable of performing a bus cycle without inserting any
			additional wait states. To perform a 16-bit memory cycle without wait
			states, this signal is derived from an address decode.
41	(B9)	+12V	+12 Volts
42	(B10)	GND	Not connected (Key Pin)
43	(B11)	SMEMW*	System Memory Write – This signal is used by bus owner to request a
			memory device to store data currently on the data bus and only active
			for the lower 1MB. Used for legacy compatibility with 8-bit cards.
44	(B12)	SMEMR*	System Memory Read – This signal is used by bus owner to request a
			memory device to drive data onto the data bus and only active for lower
			1MB. Used for legacy compatibility with 8-bit cards.
45	(B13)	IOW*	I/O Write – This strobe signal is driven by the owner of the bus (ISA
			bus master or DMA controller) and instructs the selected I/O device to
			capture the write data on the data bus.
46	(B14)	IOR*	I/O Read – This strobe signal is driven by the owner of the bus (ISA bus
			master or DMA controller) and instructs the selected I/O device to drive
			read data onto the data bus.
47	(B15)	DACK3*	DMA Acknowledge 3 – Used by DMA controller to select the I/O
			resource requesting the bus, or to request ownership of the bus as a bus
			master device. Can also be used by the ISA bus master to gain control
			of the bus from the DMA controller.

ReadyBoard 700 Reference Manual 29