Ampro Corporation 700 manual Pin # Signal Descriptions J14 Row C

Chapter 3			Hardware
	Pin #	Signal	Descriptions (J13 Row B)
	48 (B16)	DRQ3	DMA Request 3 – Used by I/O resources to request DMA service.
			Must be held high until associated DACK3 line is active.
	49 (B17)	DACK1*	DMA Acknowledge 1 – Used by DMA controller to select the I/O
			resource requesting the bus, or to request ownership of the bus as a bus
			master device. Can also be used by the ISA bus master to gain control
			of the bus from the DMA controller.
	50 (B18)	DRQ1	DMA Request 1 – Used by I/O resources to request DMA service.
			Must be held high until associated DACK1 line is active.
	51 (B19)	REFRESH*	Memory Refresh – This signal is driven low to indicate a memory
			refresh cycle is in progress. Memory is refreshed every 15.6 usec.
	52 (B20)	SYSCLK	System Clock – This is a free running clock typically in the 8MHz to
			10MHz range, although its exact frequency is not guaranteed.
	53 (B21)	IRQ7	Interrupt Request 7 – Asserted by a device when it has pending interrupt
			request. Only one device may use the request line at a time.
	54 (B22)	IRQ6	Interrupt Request 6 – Asserted by a device when it has pending interrupt
			request. Only one device may use the request line at a time.
	55 (B23)	IRQ5	Interrupt Request 5 – Asserted by a device when it has pending interrupt
			request. Only one device may use the request line at a time.
	56 (B24)	IRQ4	Interrupt Request 4 – Asserted by a device when it has pending interrupt
			request. Only one device may use the request line at a time.
	57 (B25)	IRQ3	Interrupt Request 3 – Asserted by a device when it has pending interrupt
			request. Only one device may use the request line at a time.
	58 (B26)	DACK2*	DMA Acknowledge 2 – Used by DMA controller to select the I/O
			resource requesting the bus, or to request ownership of the bus as a bus
			master device. Can also be used by the ISA bus master to gain control
			of the bus from the DMA controller.
	59 (B27)	TC	Terminal Count – This signal is a pulse to indicate a terminal count has
			been reached on a DMA channel operation.
	60 (B28)	BALE	Buffered Address Latch Enable – This signal is used to latch the LA23
			to LA17 signals or decodes of these signals. Addresses are latched on
			the falling edge of BALE. It is forced high during DMA cycles. When
			used with AENx, it indicates a valid processor or DMA address.
	61 (B29)	+5V	+5 volt power ±10%
	62 (B30)	OSC	Oscillator – This clock signal operates at 14.3MHz. This signal is not
			synchronous with the system clock (SYSCLK).
	63 (B31)	GND	Ground
	64 (B32)	GND	Ground

Notes: The shaded area denotes power or ground. The signals marked with * = Negative true logic.

Table 3-7. PC/104 Interface Pin/Signal Descriptions (J14C)

Pin #	Signal	Descriptions (J14 Row C)
1 (C0)	GND	Ground
2 (C1)	SBHE*	System Byte High Enable – This signal is driven low to indicate a
		transfer of data on the high half of the data bus (D15 to D8).
3 (C2)	LA23	Lactchable Address 23 – This signal must be latched by the resource if
		the line is required for the entire data cycle.
4 (C3)	LA22	Lactchable Address 22 – Refer to LA23, pin-C2, for more information.

30 Reference Manual ReadyBoard 700