Ampro Corporation 700 manual Chapter Bios Setup

Page 73

Chapter 4

BIOS Setup

♦PnP OS – [Disabled] or [Enabled]

If this field is set to [Enabled], the BIOS makes the Plug and Play API available for Plug and Play Operating Systems. This allows the Plug and Play OS to get the Plug and Play information by calling the Plug and Play API.

♦Assign IRQ 1 – [Disabled] or [Enabled]

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦ Assign IRQ 3 – [Disabled] or [Enabled] (Typically COM2)

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦ Assign IRQ 4 – [Disabled] or [Enabled] (Typically COM1)

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦Assign IRQ 5 – [Disabled] or [Enabled]

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦ Assign IRQ 6 – [Disabled] or [Enabled] (Typically Floppy Disk)

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦ Assign IRQ 7 – [Disabled] or [Enabled] (Typically LPT1)

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦ Assign IRQ 9 – [Disabled] or [Enabled] (Typically unused)

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

♦ Assign IRQ 10 – [Disabled] or [Enabled] (Typically unused)

•If this field is set to [Enabled], then the BIOS can assign this IRQ to a Plug and Play adapter.

•If another device in the system is using this IRQ, then this field should be set to [Disabled].

ReadyBoard 700

Reference Manual

67

Image 73

Contents ReadyBoard Single Board Computer Reference Manual Revision History Audience AssumptionsContents Appendix a List of Tables Reference Manual ReadyBoard Purpose of this Manual SpecificationsReference Material ReadyBoard 700 Support Products Related Ampro ProductsOther ReadyBoard Products Other Ampro ProductsChapter Reference Manual ReadyBoard Epic Architecture Product OverviewProduct Description Board FeaturesChapter Chapter ATA Block DiagramChip Type Mfg Model Description Function Major Integrated Circuits ICsCPU VIASwitch Definition Connector DefinitionsJack # Signal/Device Description Component DescriptionLvds J7 All illustrationsIllustrations Additional ComponentsJumper # Installed Removed Power/IDE LED DefinitionsIndicator Definition Jumper DefinitionsJumper, Switch, and LED Locations Top view Physical Specifications SpecificationsPower Specifications Environmental SpecificationsThermal/Cooling Requirements Mechanical SpecificationsReadyBoard 700 Side view Overview Chapter HardwareMemory CPU U4Sdram Memory DIMM1 Flash MemoryMemory Map Interrupt Channel AssignmentsBase Address Function Address MapAddress hex Subsystem CF8-CFFPC/104-Plus Interface J12 Pin # Signal Input Description OutputGNT1 REQ0CLK2 PerrCLK0 REQ2Intd IntaREQ1 IDSEL1GNT2 CLK3IDSEL3 IDSEL2GNT0 CLK1PC/104 Interface J13 A/B, J14 C/D Pin # Signal Description J13 Row aPin # Signal Descriptions J13 Row B Pin # Signal Descriptions J14 Row C Pin # Signal Descriptions J14 Row D DACK5 DRQ0DRQ5 DACK6IDE Interface J22 Pin # Signal DescriptionPdior PdiowPdiordy PdcselCompactFlash Adapter J23 CFD1 CFD2SDD11 SDD12Floppy/Parallel Interface J20 Step SlctinAutofdx DrvenoRS485 Serial Port Implementation Serial Interfaces J5A/B, J3A/BSerial a Interface J5A/B Serial B Interface J3A/B DTR4 CTS4Primary USB0 and USB1 J15A/B USB Interfaces J15A/B, J21A/BSecondary USB2 and USB3 J21A/B Pin # Ethernet Interfaces J10, J11Digital Ground Audio Interface J19 CRT Interface J8 Video Interfaces J8, J9, J7LCD Interface J9 Lvds Interface J7 Pin # Signal Description Line ChannelMiscellaneous Reset Switch SW1Utility Interface J18 Keyboard/Mouse Interface J16Infrared IrDA Port J17 Oops! Jumper Bios RecoveryReal Time Clock RTC IrtxTemperature Monitoring User Gpio Signals J2Serial Console Serial Console Setup Watchdog TimerPower In Interface J4 Power Interfaces J4, J6Power-On Interface J6 VccsbReference Manual ReadyBoard Introduction Accessing Bios Setup VGA DisplayBios Setup Menu Item/Topic Accessing Bios Setup Serial ConsoleBios Setup Opening Screen Bios MenusDate & Time Bios Configuration ScreenDrive Assignments Boot Order # of Floppy Drives Bios SettingsDrive and Boot Options User Interface Keyboard and Mouse ConfigurationMemory Advanced features Power ManagementChapter Bios Setup On-Board LPT Port On-Board Serial PortsOn-Board Video On-Board ControllersPanel Type 640 x 480 x 18 TFT LCD ResolutionType 640 x 480 x 18 bitChapter Bios Setup Chapter Bios Setup Chapter Bios Setup Splash Screen Image Requirements Splash Screen CustomizationConverting the Splash Screen File \splashconvert convert.idf Reference Manual ReadyBoard Method Contact Information Appendix a Technical SupportAppendix a Appendix B LAN Boot Option Accessing PXE Boot Agent Bios Setup PXE Boot Agent Bios SetupPXE Configuration PXE Boot Agent Setup ScreenTCP/IP Configuration RPL Configuration NetWare ConfigurationLED CD-ROMPost RTCWatchdog timer WDT Table notes Reference Manual ReadyBoard