JVC DLA-G150CLU Projector’s buttons Select the Input source to be Projected, Second or more

OPERATE

Remote control unit

Basic Operations

Basic Operations

■ Projector’s buttons	The following describes the basic procedure for normal use
	of the projector.

■Projector’s buttons

2. Select the Input source to be Projected

		STAND BY indicator
	STAND	BY
LAMP TEMP		OPERATE indicator
	OPERATE
HIDE		OPERATE button
	PC
KEYSTONE
	VIDEO
PRESET	MENU
EXIT	ENTER

1. Turning on the Power

1 Turn on the MAIN POWER switch.

ON [ ❙]:The main power turns on and the STAND BY indicator comes on.

Projector’s indicator

STAND BY

OPERATE

2Press the OPERATE button for one second or more.

•The OPERATE indicator lights and the projected screen slowly appears.

STAND BY

LAMP TEMP

	OPERATE
	HIDE
	PC
KEYSTONE
	VIDEO
PRESET	MENU
EXIT	ENTER

■ Remote control unit

PC button

VIDEO button

Press the VIDEO button or the PC button to switch the input.

•Each time you press either button, the selected input changes as follows. The selected name appears on the top right of the image on the screen for five seconds. (Called line display.)

When selecting an image device connected to the AV IN (VIDEO, Y/C or COMP) terminal:

Projector

Press VIDEO.

The input mode changes as follows every time the button is pressed.

VIDEO ↔ Y/C ↔ COMP

Remote control unit

Press the “VIDEO”, “Y/C” or “COMP” button.

VIDEO: The image from the VIDEO input terminal on the

side of the unit is projected.

OPERATE

STAND BY

Y/C: The image from the Y/C input terminal on the side of

or

Notes

OPERATE

QUICK

ALIGN.			OPERATE
	HIDE			PC button
W
SCREEN	FREEZE	COMP	VIDEO
S				VIDEO button
PC1	PC2	DVI	Y/C
	T	T		ZOOM button
KEYSTONE	DIGITAL	ZOOM	FOCUS
	ZOOM

the unit is projected.
COMP: The image from the COMP (Y, R	B /B-Y, P R /R-Y)
input terminal on the side of the unit is projected.

*When there is no signal from the selected input terminal (No signal), “No Input” is displayed.

No.51931

■Remote control unit

•After the power is turned on, the image may be jumbled for a few seconds, but this is not a malfunction.

•After the indicator comes on, it can take a minute or so for the lamp to warm up and operate consistently.

■Turning off the Power

1 Press the OPERATE button for one

second or more.

W	W
PRESET	MENU
EXIT	ENTER
RM-M160 REMOTE CONTROL UNIT

When selecting a device such as a computer which is connected to the PC1, PC2 or DVI terminal:

Projector

Press PC.

The input mode changes as follows every time the button is pressed.

PC1 ↔ PC2 ↔ DVI

QUICK

ALIGN.			OPERATE	OPERATE button
	HIDE
W
SCREEN	FREEZE	COMP	VIDEO
S
PC1	PC2	DVI	Y/C
	T	T
KEYSTONE	DIGITAL	ZOOM	FOCUS
	ZOOM
	W	W
	PRESET		MENU
	EXIT		ENTER
	RM-M160 REMOTE CONTROL UNIT

• The STAND BY indicator changes to blinking, and the

projector goes into cool-down mode. The cool-down

mode will continue for approximately 120 seconds. Projector (Blinking)

STAND BY

OPERATE

Note

•The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Use the button after approximately 1 minute.

2Turn off the MAIN POWER switch after the STAND BY indicator changes to

steady on.

OFF [ ‡]:The MAIN POWER switch turns off and the

STAND BY indicator goes off.

Projector

STAND BY

OPERATE

■Language display

The display languages of the menus, direct buttons (DIGITAL ZOOM, KEYSTONE, etc) and messages is set to “ENGLISH” when the projector is bought. The display language can be selected from the following 6 languages:

(Japanese)”, “English (English)”, “Deutsch (German)”, “Español (Spanish)”, “Italiano (Italian)” and “Français (French)”. (Refer to page 46.) However, some words (VIDEO, NTSC, Quick Alignment, etc) are only displayed in English.

Remote control unit

Press the “PC1”, “PC2” or “DVI” button.

PC1: The image from the PC1 input terminal on the side of the unit is projected.

PC2: The image from the PC2 input terminal on the side of the unit is projected.

DVI: The image from the DVI input terminal on the side of the unit is projected.

*When there is no signal from the selected input terminal (No signal), “No Input” is displayed.

Remote	control		unit	Projector
SCREEN	FREEZE	COMP	VIDEO	PC
S
PC1	PC2	DVI	Y/C	VIDEO

[Screen display]
	VIDEO	Line Display
		PC 1	COMP
	Q U I C K A L I G N M E N T
		PC 2	DVI
		Y/C
		VIDEO

* To show the line display (Y/C, VIDEO, COMP, PC1, PC2 or

ITALIANO FRANÇAISDEUTSHENGLISH

CAUTION

• Do not turn off the MAIN POWER switch during cool-down mode (the STAND BY indicator blinking). Turn it off after the STAND BY indicator becomes on (stand-by mode).

32

1-17

DVI) or not is selectable by the menu. Refer to “Setting and Adjusting Other Functions (OPTIONS)” on page 54.

Note

•When no image signal is input to the selected input terminal, the message “No Input” is displayed on the screen. (Refer to page 67.)

33

ESPAÑOL

DLA-G150CLU DLA-G150CLE