JVC DLA-G150CLE, DLA-G150CLU manual Cleaning and Replacing the Filter Cover

1-32

Replacing the Light-Source Lamp

■Resetting the Lamp Use Time

After replacing with a new light-source lamp, reset the lamp-time counter inside the projector to clear the accumulated lamp time to zero (0). After resetting, a new count will start for the new light-source lamp.

Cleaning and Replacing the Filter Cover

Clean the filter regularly. If the filter is heavily stained and does not clean, or if it is damaged, replace the filter with a	new filter.
Otherwise, dirt may get inside and appear on the screen, preventing you from fully enjoying the video image. If dirt gets insid	e
or if you need information about the filter, consult authorized dealer where you purchased the projector or the nearest Service
Center.

DLA-G150CLU DLA-G150CLE

■ Projector’s button

STAND BY indicator

1Turn on the MAIN POWER switch to go

into stand-by mode.

In stand-by mode, the STAND BY indicator on the projector lights up.

1Turn off the MAIN POWER switch.

After the projector goes into stand-by state with the STAND BY indicator on, turn off the MAIN POWER switch and pull out the power cord from the projector and the wall outlet.

2Remove the filter.

4HIDE button

3EXIT button

STAND BY

LAMP TEMP

	OPERATE
	HIDE
	PC
KEYSTONE
	VIDEO
PRESET	MENU
EXIT	ENTER

Cursor buttons 5/∞

OPERATE indicator

1PC button

MENU button

2ENTER button

2Press the following buttons on the projector, sequentially.

1Momentary press the PC button.

2Momentary press the ENTER button.

3Momentary press the EXIT button.

4Press and hold the HIDE button for two seconds

or more.

* During this sequence, the STAND BY and OPERATE

indicators alternately blink about every approx. 3 seconds. After completion of the sequence, the STAND BY indicator alone stays on.

*Buttons must be pressed within 2 seconds of the previous button.

*When you make a mistake in button operations, return to the beginning of the sequence.

*To check the lamp time on the menu, press the MENU button

and select “Information” with the cursor button 5 or∞. The lamp use time is indicated in the item “Lamp time”.

Loosen the screw with a flat-end screwdriver.

Screw

Filter

Be careful not to damage the claws.

Notes

• The screw is fitted so that it does not come off the filter.

• If the filter is clogged with dirt, etc., the projector goes into an warning state (the OPERATE and STAND BY indicator blink.

No.51931

Video main		menu
	Menu
	Image adj.	Input	VIDEO
	Setting	Switcher		CH.0
	Color temp.	Source	NTSC
	Options
	Language
		Lamp time		123 h
	Information
PC main menu
	Menu
	Image adj.	Input		PC 1
	Setting	Switcher		CH.0
	Color temp.	Resolution	1280	1024
	Options	Frequency H	79.9kHz
	Language	Frequency V	75 Hz
		Lamp time	123	h
	Information

Lamp time (0 h)

Lamp time (0 h)

etc.). Therefore regularly, clean the filter. For the warning indication, refer to page 67.

3Clean the filter.

Clean the filter with a neutral detergent, wash it in water, and then dry it in the shade.

CAUTIONS

• Put on rubber gloves when using neutral detergent.

• After you have washed the filter in water, make sure the filter is completely dry before reinstalling it, otherwise an electri c shock or malfunction could occur.

• Do not clean the filter using a vacuum cleaner. Since the filter is soft, it may be sucked into the vacuum cleaner or damaged.

FRANÇAISDEUTSHENGLISH

CAUTION

• Reset the lamp use time only when you have replaced with a new light-source lamp. Never reset it during lamp life, otherwise the replacement time may become unclear, and lead to degraded performance or lamp explosion.

62

4Reinstall the filter.

Fasten the screw with a flat-end screwdriver.

Notes
• Install the filter correctly. Otherwise, the projector does not operate. (Goes into an warning state (For the warning indicati	on,
Refer to page 66).)

•If the filter’s claws (in particular the claw which is hidden behind the filter cover knob) are damaged, the projector may not operate. Then, replace with a new filter.

63

ESPAÑOLITALIANO