JVC DLA-G150CLU, DLA-G150CLE manual Bottom Surface, Control Panel on the Projector

No.51931

Controls and Features

Bottom Surface

t

y u

i

tAir inlet (filter)

Air is taken in through the filter to cool the light-source lamp. If the filter is blocked or if something that obstructs the flow of air is placed around the projector, heat may build up inside and could cause a fire. For required

space, refer to “Precautions for Installation” on page 15.

CAUTIONS

• Be careful as paper, cloth or soft cushion could be drawn in if placed nearby. Do not block the filter, or heat may build up and could cause a fire.

• Clean the filter periodically. For details, refer to “Cleaning

and Replacing the Filter Cover” on page 63. Deposition of

dirt on the filter reduces the cooling effect, causing heat to

build up inside, which could cause a fire or malfunction.

Controls and Features

Control Panel on the Projector
r		1
e
	LAMP TEMP	STAND	BY	2
		OPERATE
w	HIDE			3
q		PC		4
	KEYSTONE			5
		VIDEO
	PRESET	MENU
p				6
9				7
8	EXIT	ENTER
1 STAND BY Indicator	Memo

ON :	When in stand-by mode.
		While in the cool-down mode (STAND BY indicator is blinking):
Blinking :When in cool-down mode.
		Even if you press the OPERATE button, the projector is not
		turned on. Wait until the projector enters stand-by mode
Memo
		(STAND BY indicator stays lit).
About the cool-down mode:
		4 PC button
This projector has a function to cool down the heated lamp for a
fixed period of time (approx. 120 seconds) after projection is		Use this button to select a device connected to the PC 1,
finished. This feature is referred to as the cool-down mode.		PC 2 or DVI terminals. Each time you press the button,
The purpose of the cool-down mode is to prevent inner parts		the selection alternates among PC 1, PC 2 and DVI.
from being deformed or broken by heat from the heated lamp		* “PC1” , “PC2” or “DVI” will be displayed on the top right of
as well as to prolong the life of the lamp.		the projected image. (This function can be disabled by
		the menu.)
CAUTIONS		5 VIDEO button

yOpening for replacing the light-source lamp For replacing the light-source lamp, refer to “Replacing the Light-Source Lamp” on page 58.

uFixing foot

iPosition selecting screw for ceiling mounting When using the projector in an upside-down, ceiling-

mounted position (inverted top-to-bottom and right-to- left), the “position selecting screw for ceiling mounting” must be turned to switch to ceiling mounting.

This will correct variance in color images (shading), which otherwise would occur in ceiling mounting.

For more information, refer to “Setting the Position Selecting Screw for Ceiling Mounting” on page 21.

CAUTION

•To ceiling-mount and adjust the projector, special expertise and technique are necessary. Be sure to ask your dealer or specialist to perform this work.

•Do not turn off the MAIN POWER switch while in the cool- down mode.

•Do not place the projector on its side or stand it upright while in the cool-down mode; this may block the vents.

2OPERATE indicator

ON : When the projector is in operation (projecting).

OFF : When the projector is not in operation (not projecting).

3OPERATE button

When the projector is in the stand-by mode, press this button one second or more, and the projector is turned on, causing the OPERATE indicator to light.

Press it one second or more again, and the projector goes into the cool-down mode, then stand-by mode. (Refer to page 32.)

* You cannot use the OPERATE button for about one minute after the lamp blinks. Press the button after a minute or longer has elapsed.

Use this button to select a device such as a video deck connected to the AV IN (Y/C, VIDEO or COMP) terminal

of the projector. Each time you press the button, the selection alternates among Y/C, VIDEO and COMP.

*“Y/C”, “VIDEO” or “COMP” will be displayed on the top right of the projected image. (This function can be disabled by the

menu.)

6MENU button

Use this button to enter or exit the menu mode. The main menu appears or disappears at the screen. For details, refer to “Basic Menu Operation” on page 43.

7ENTER button

This button will be used in the menu mode. Use to display the hierarchical menus. Also use when “ENTER” is displayed against the item on the menu screen or

when the “All reset” selection is confirmed. For details, refer to “Basic Menu Operation” on page 43.

8Cursor buttons 5/∞/2/3

These buttons will be used in the menu mode to select an

item, or to set or adjust the value. For details, refer to “Basic Menu Operation” on page 43.

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

DLA- DLA-

1-5

8

9

G150CLU G150CLE

DLA-G150CLU