JVC DLA-G150CLE, DLA-G150CLU manual Setting the Position Selecting Screw for Ceiling Mounting

Page 52

1-52

No.51931

Installing the Projector

Setting the Position Selecting Screw for Ceiling Mounting

When using the projector in an upside-down, ceiling-mounted position (inverted top-to-bottom and right-to-left), the “position selecting screw for ceiling mounting” must be turned to switch to ceiling mounting.

This will correct variance in color images (shading), which otherwise would occur in ceiling mounting.

To revert to normal desktop setting, turn the “position selecting screw for ceiling mounting” back to the initial position (fac tory- shipped).

When using the projector in an upside-down, ceiling-mounted position:

Turn the “position selecting screw for ceiling mounting” fully counterclockwise (until it is turning idly).

To again use the projector in a normal desktop setting:

Turn the “position selecting screw for ceiling mounting” fully clockwise (until it firmly tightens).

For normal desktop mounting:

Turn the screw clockwise.

For upside-down, ceiling-mounting:

Turn the screw counterclockwise.

CAUTIONS

•To ceiling-mount and adjust the projector, special expertise and technique are necessary. Be sure to ask your dealer or a specialist to perform this work. •To turn the “position selecting screw for ceiling mounting”, use a Phillips screwdriver with a 30-mm or longer shank.

The screw is located in the hole shown in the illustration.

Position selecting screw for ceiling mounting

Note

•When using the projector in a ceiling-mounted position, you should reverse the projected image by changing the settings of Right Left rev. and Top Bottom inv. menus. For details, refer to page 54. You can also change these settings without receiving a video signal. In this case, refer to “Menu Transition Diagram in No signal Menu Mode” on page 38.

When installing (adjusting/setting) the unit

• When using “Top Bottom inv.” on the “Options” menu, reset the unit by following the procedure below.

•This reset procedure must be performed before operating the unit.

1.Change the “Top Bottom inv.” Setting on the “Options” menu.

2.Press the OPERATE button to enter the unit into the stand-by mode.

3.Press the OPERATE button again to turn on the unit.

•Adjust the focus after projecting a picture for 30 minutes or longer.

21

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

Connecting to Various Devices

Before connection, be sure to turn off the projector and connected devices.

Read the manual which comes with each device thoroughly.

Signals that Can Be Input to the Projector

The following signals can be input to the projector:

■Video signals

(1)Response to color systems systems

Input terminal

NTSC

NTSC4.43

PAL

SECAM

 

 

 

 

 

 

 

 

 

VIDEO

‡

‡

‡

‡

 

 

 

 

 

Y/C

‡

1

‡

- - - - -

‡*

Y, P B /B-Y, P R /R-Y

2

2

2

2

‡*

‡*

‡*

‡*

G, B, R, H/C S , V

2

2

2

2

‡*

‡*

‡*

‡*

*1:Responds if Y/C output is available.

 

 

 

*2:Signifies that component signals (“Y, P

B , P R ” / “Y, B-Y, R-Y” / “G, B, R, H/C S , V”) conform to the signal timing

(synchronization and video period) of each color system. The color systems are used for convenience only.

 

(2)Response to double density (*3), high-vision signals

Input terminal

NTSC*

4

NTSC*

5

High-vision signal

 

 

 

 

 

 

 

 

Y, P B /B-Y, P R /R-Y

‡

 

‡

 

‡

 

 

 

 

 

 

G, B, R, H/C S , V

‡

 

‡

 

‡

 

 

 

 

 

 

*3:Signals whose density of scanning lines/field is twice as high.

*4:Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded wide-clear-vision signal and decoded 525P progressive signal.

*5:Responds to signals whose horizontal scanning frequency is 33.5 kHz. PAL can be made twice as dense by a line doubler

(separately available: recommended article).

 

 

 

 

(3) Response to DTV-format signals

 

 

 

 

DTV-format signals (480i, 480p, 720p, 1080i) can be input to the Y, P

B /B-Y, P R /R-Y, G, B, R, H/C

S , V input terminal.

■ Computer signals

 

 

 

 

Signals with the following scanning frequencies can be input to the PC 1 or PC 2 (G, B, R, H/C

S , V) and DVI terminals.

 

 

 

 

 

Horizontal scanning frequency

15kHz - 105kHz

 

 

 

 

 

 

 

 

Vertical scanning frequency

50Hz - 100Hz

 

 

 

 

 

 

 

 

Be sure that the computer to be used suffices the following conditions:

• The computer has the video signal output port.

Be sure that the computer has the video signal output port by reading the instruction book of the computer.

The video signal output port is generally called as “RGB port”, “monitor port”, or “video port”. If the computer-monitor hybrid type or note type is used, it may need to prepare for an external output port. Also, there will be the type to which an externa l output port cannot be installed.

• DVI input

During DVI input, depending on the computer settings, there may be no signal input or an error may occur (blue screen).

If this happens, turn off the power to both the projector and the computer, and then turn the projector back on before turning the computer on again. Then correctly set the computer's graphic board.

• The resolution and the scanning frequencies are within the range specified in the table on page 23.

Be sure that the resolution and the scanning frequencies of the video signal are within the range. A video signal out of range cannot be used. (Even signals out of the range could be projected. However, it may not sharp enough. On the other hand, even some of the signals within the range may require adjustment depending on the video board used.)

When a signal other than listed in the table on page 23 is input, the image could be partially erased or an unneeded fold-over image could appear.

Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal. Composite sync (C S ) and G on Sync signals cannot be handled depending on the devices connected.

22

DLA-G150CLU DLA-G150CLE

Page 51 Page 53
Image 52
Page 51 Page 53
Contents DLA-G150CLU About the installation place Do not allow any unqualified person to install the unitAbout burning-in of the D-ILA device Can ResultContents Controls and Features Bottom Surface Control Panel on the ProjectorConnector Panel Remote Control Unit Installing Batteries Installing the ProjectorPrecautions for Installation Adjusting the Inclination of the Projector Installing the Projector against the ScreenAdjusting the vertical angle of the projector Leveling the projectorSetting the Amount of Lens Shifting Projection Distance and Screen SizeEffective Range and Distance of the Remote Control Unit Setting the Position Selecting Screw for Ceiling MountingWhen installing adjusting/setting the unit Using as a wireless remote control unitConnecting to Various Devices Signals that Can Be Input to the ProjectorVideo signals Allowable input signalsConnecting to Video Devices Connecting to Hi-Vision Devices/DVD PlayersConnecting to Other Devices Connecting to Devices which Control the ProjectorTo Control Game device, etc Desktop typeConnecting to DVI Connecting to Computer DevicesHow to attach the ferrite core Lamp control settings Basic OperationsRemoving the Lens Cap To prevent fire and electric shock, observe the followingTurning on the Power Turn on the Main Power switch Remote control unitTurning off the Power Projector’s buttonsSetting the Screen Aspect Ratio Remote control unit Turning off Image HideRemoving the Trapezoidal Distortion of the Image Zooming a Part of the Image Remote control unit Quick Alignment FunctionDisplaying a Still Picture Freeze Menu Transition Diagram in No signal Menu Mode Menu Transition Diagram in Video Menu ModeQuick Reference Guide for No signal Menu Mode Submenus in Video Menu ModeMenu Transition Diagram in PC Menu Mode For Video Menu ModeQuick Reference Guide Factory set valuePress the cursor Button 2 or 3 to set Or adjust the value Quick Reference Guide for PC Menu ModeRemote control unit Projector Basic Menu OperationChanging the Color System Video Menu Mode Only Video menu modePC menu mode ProjectorAdjusting Tracking/Phase Adjust the Screen aspect ratioChanging the Language Display Or Hdtv with the cursor button 5 or ∞Set up for Watching Image Software Video Menu Mode Only Adjusting Picture QualitySelect the item to be adjusted with the cursor button5 or ∞ Make adjustment with the cursor2 orAdjusting the Video Screen/Menu Position Adjusting Color temperatureAdjust the color temperature with Cursor button2 or Cursor button Or ∞Changing the Image Gamma/Aspect Ratio Video Menu Mode Only Changing the Image Size Resize Function PC Menu Mode OnlySelect Gamma or Aspect ratio with the cursor button5 or ∞ Select Resize with the cursor button 5 or ∞Setting and Adjusting Other Functions Options Adjustment item ButtonOr∞, and press the Enter button Or∞, and pressReplacing the Fuse Getting InformationSelect Information with the cursor button5 or ∞ Projector and the wall outletReplacing the Light-Source Lamp Light-source lamp and lamp use timeReset the lamp use time Insert the new light-source lamp fullyInside and fasten the screws Loosen the screws, raise the handleCleaning and Replacing the Filter Cover Maintenance TroubleshootingWhen warning indication is shown by the blinking indicators Indication Indicator Action to be taken for warning indicationLamp Temp OperateTo cancel this message, press Power Control Mode LPCMessage is cleared by Pressing any buttonSpecifications GL-M2915SGEnglish Deutsh Français Italiano Español Outside dimensions Pin assignment Specifications for terminalsCommunication Specifications Command FormatControl command table RS-232C external controlAppendix ForDLA-G150CLEINSTRUCTIONS To the following power supply voltage. Use only Power cord designated by our dealer to ensure SafetyFire Hazard EMCReplacing 15the United Kingdom onlyVarious Devices Front Side / Top Surface / Right Side Approx mFerrite core ⋅ Conversion adapter for Mac for Macintosh BNC-RCA Conversion plug DeutshRear adjustable foot for leveling the projector Stand by Indicator Control Panel ProjectorButton to obtain a still picture Button does not workPC buttons Gebruike batterijenInstalling the Projector English GL-M2930SZGRemote control unit Response to color systems systems To Video Video cable accessory Hor Pixels Ver Lines KHz PC system PC98640 350 37.86 640 400 24.83 56.42BNC-RCA conversion plug accessory To Video To Y To PB/B-YGame device, etc Hi-Vision devices VHS VCRConnector Connection cable supplied To RS-232C connector To Remote terminal To monitorCable Supplied Ferrite core Basic Operations Side of the unit is projected Comp The image from the Comp Y, RPressed PC1 ↔ PC2 ↔ DVI Image will be displayed in fullNo.51931 Quick Alignment Function Quick AlignMain menu in No signal Menu Mode Quick Reference Guide For Video Menu Mode Options → Refer to Phase Flickering or dim picture image can be adjusted toInformation → Refer to Restored Menu returns to the previous menuAuto Adjusting Tracking/Phase Image adj. submenu appears on the screen Adjust the color temperature with Cursor button 2 orOr ∞, and press the Enter button. Then, the All Video submenu Video submenu Set up 1 submenu Españolitaliano Françaisdeutshenglish Image enlarged to the full size 1365 ⋅Press the Menu button to exit the menu mode Exceeds 2000 hoursReplacing the Fuse Cover by loosening screws Stand by indicator Projector’s button Turn on the Main Power switch to goScrew Lamp-replacement opening cover Hide button With Blocked?When warning indication is shown by the blinking indicators Message Cause Corrective action Specifications Optical mechanism systemElectrical system Input terminalsGeneral FrontUnit mm 21h Control command to the projector Designates the terminal of the data DhFunction Command Asking Operation Mode parametersFor lens unit GL-M2910G Español 2002 Victor Company of JAPAN, Limited

DLA-G150CLU, DLA-G150CLE specifications

The JVC DLA-G150CLU and DLA-G150CLE projectors represent the pinnacle of home cinema and professional presentations, offering exceptional picture quality and advanced technological features. Both models are designed to deliver an immersive viewing experience, leveraging JVC’s years of expertise in projection technology.

These projectors incorporate JVC’s renowned D-ILA (Direct-drive Image Light Amplification) technology. This innovative system utilizes liquid crystal on silicon to achieve stunning color accuracy and contrast. The DLA-G150CLU and DLA-G150CLE boast an impressive native resolution of 1920x1080, allowing for incredibly detailed images that are perfect for both high-definition films and intricate graphics. The contrast ratio of these projectors reaches up to 20,000:1, making dark scenes richer and more dynamic while ensuring bright areas remain vivid without washing out.

Color reproduction is another strong point of the JVC DLA-G150 series, featuring an expansive color gamut that adheres closely to industry standards. The projectors utilize a dual-lamp system, allowing for increased brightness levels of up to 2500 lumens, which ensures clear visibility even in well-lit environments. This feature is particularly beneficial for presentations in conference rooms or larger venues where ambient light may compromise image quality.

Both the DLA-G150CLU and DLA-G150CLE support a wide range of connectivity options, including HDMI and RS-232 ports, making them versatile for various setups. This connectivity is further enhanced by an intuitive on-screen menu system, allowing users to easily adjust settings and calibrate the projector for optimal performance.

For those who value flexibility, the JVC DLA-G150 projectors come with lens shift capabilities, enabling vertical and horizontal adjustments. This feature allows users to position the projector without compromising image quality, catering to different installation environments.

In conclusion, the JVC DLA-G150CLU and DLA-G150CLE projectors embody the perfect blend of advanced technology and user-friendly features. Whether used for home entertainment or professional applications, they offer unparalleled performance, making them an excellent choice for anyone seeking high-quality projection solutions.
Top Page Image Contents