JVC DLA-G150CLE Setting and Adjusting Other Functions Options, Or∞, and press the Enter button

1-28

No.

Menu Operations

Setting and Adjusting Other Functions (OPTIONS)

Various functions are provided as shown in the “Options 1” and “Options 2” submenus.

You can set or adjust each function, as required.

1Press the MENU button.

The main menu appears on the screen.

2 Select “Options” with the cursor button 5 or ∞, and press3 or the ENTER button.

The “Options 1” submenu appears on the screen.

Options 1
Menu display	15sec	ON
Line display	5sec	OFF
Lamp time display	ON	OFF
Keystone	ENTER
Lamp control	ENTER
Page 2	ENTER

3	Select the item to be adjusted with the cursor	button5 or ∞.
4	Make adjustment with the cursor2 or 3.
	• While the keystone item is selected, press the ENTER button to display the “Keystone” submenu.
	• To enter the “Page 2” submenu, select “Page 2” with the cursor button	5 or∞, and press the ENTER button.
	• To return to the “Page 1” submenu from the “Page 2” submenu, select “Page 1” with the cursor button		5 or∞, and press
	the ENTER button.
	Keystone	123

Options ENTER

Menu Operations

Adjustment item	Button			Adjustment content
		Sets whether to clear the menu display automatically or not.
Menu display	2 or3	15sec*	: Clears the display automatically in about 15 seconds.
		ON	: Does not automatically clear the menu display.
		Sets whether to show the line display (Y/C, VIDEO, COMP, PC1, PC2 or DVI) on top
Line display	2 or3	right of the screen or not when the VIDEO or PC button is pressed.
		5sec*	: Shows the line display for about 5 seconds.
		OFF : Does not show the line display.
		Displays the lamp use time.
		ON* : Displays when the lamp use time reaches 1000 hours when set in the LPC or
Lamp time display	2 or3		LOC mode.
		OFF : Does not display when the lamp use time reaches 1000 hours when set in the
			LPC or LOC mode.3
		Press the ENTER button to enter the keystone submenu.
		In the keystone submenu, press		2 or3 to correct trapezoidal distortion of the
		projected image. (–80 ↔ 0* ↔		+128)
Keystone	ENTER	To reset the keystone (trapezoidal distortion of the picture image) to the original
		setting (factory set value: 0), press the PRESET button when the “Keystone”
		submenu appears on the screen.
		To exit the keystone submenu, press the EXIT button.
		Press ENTER to enter the lamp control submenu.
		Normal* : Used as a normal lamp.
		LPC	: Automatically controls the power used by the lamp and increases it in
			steps. When this mode is used, the brightness starts at approximately
			70%. The decrease in brightness is slower than in “Normal” mode and this
			mode is best suited when using the projector continuously for long periods
Lamp control	ENTER		of time.
			* “Lamp replacement” appears on the screen when the lamp use time
			exceeds 2000 hours.
		LOC	: The brightness can be set in seven levels (-6 to 0). Since the brightness
			can be set in steps, this is the mode best suited for adjusting multiple
			screens. This setting can also be changed while the projector is being
			used. To change the setting, choose LOC with the		5/∞ cursors and

DLA-G150CLU DLA-G150CLE

51931

Menu display	15sec	ON
Line display	5sec	OFF
Lamp time display	ON	OFF
Keystone	ENTER
Lamp control	ENTER	ENTER
Page 2	ENTER

ENTER

ENTER

Lamp control

Normal

LPC

LOC

			choose the level with the	2/3 cursors.
		Reverses image right-to-left.
Flip H	2 or3	OFF*	: For the front method.
		ON	: For upside-down hanging from the ceiling.
		Inverses image upside-down.
Flip V	2 or3	OFF*	: For normal setup.
		ON	: For upside-down hanging from the ceiling.
		Sets the baud rate for transmission.
RS-232C [bps]	2 or3	9600	: 9600 bps

DEUTSHENGLISH

ENTER	Page 2
	Flip H		OFF		ON
	Flip V		OFF		ON
	RS-232C [bps]		9600		19200
	Sleep time [min]	15	30	60	OFF
	Page 1	ENTER

*To adjust multiple items, repeat 3 to 4.

*To reset the keystone (trapezoidal distortion of the picture image) to the original setting, press the PRESET button when the “Keystone” submenu appears on the screen.

54

		19200* : 19200 bps
Sleep time [min]	2 or3	Sets the length of sleep time which automatically brings the projector into stand-by
		state. You can select one of the sleep times: 15, 30, 60 and 0 (OFF*) minutes.
* Factory set value

5Press the EXIT button to return to the previous menu or press the MENU button to exit the menu mode.

Note

• Refer to “Removing the Trapezoidal Distortion of the Image” on page 35 for more details about adjusting the keystone.

55

ESPAÑOLITALIANO FRANÇAIS