JVC DLA-G150CLE, DLA-G150CLU manual Replacing the Fuse

Page 70

1-70

Replacing the Fuse

A fuse is used to protect the power source of the projector. If the fuse is blown, replace it. When the power switch is turned

on

but no power is supplied to the projector, check the fuse. If there are any unclear points, contact the dealer where you

 

purchased your projector, or consult the Service center.

 

CAUTION

When replacing the fuse, use the same rating and type (T6.3A H 250 V). Otherwise, a fire may occur and/or the projector may be damaged.

Replacing the Light-Source Lamp

Light-source lamp and lamp use time

The light-source lamp has a service life of approximately 1000 hours.

[Average lamp life: 1000 hours (brightness half-life)]

When the light-source lamp approaches the end of its service life, degradation progresses rapidly. In NORMAL MODE,

arrange for a new lamp (lamp unit) or replace the lamp after 900 hours. Depending on the usage conditions, the replacement time may be shorter.

(In LOC and LPC modes, the brightness of the lamp is electrically controlled and the replacement time is extended. Arrange

DLA-G150CLU DLA-G150CLE

1Turn off the main power switch and disconnect the power cord from both

the projector and the wall outlet.

In stand-by state (the STAND BY indicator lights on), place the MAIN POWER switch of OFF [ ] position.

2Loosen the fuse holder to remove it.

To loosen the fuse holder, use a Flat-end screwdriver.

for a new lamp (lamp unit) or replace the lamp after 1900 hours. Depending on the usage conditions, the replacement time may be shorter.)

If, even after adjusting the brightness or color, the video image is dark or the color is not correct, replace the lamp early. The lamp use time can be checked. Look at the “Lamp time” which is displayed with the “Information” option in the menu.

(Refer to page 40, 42.)

Contact the store from where you purchased the projector or the JVC service center for details about purchasing replacement lamps.

Replacement lamp (lamp unit) part number: BHL 5001-SU

The LAMP indicator and the message on the screen warn you that replacement of the lamp is required, as follows:

Projecting after the lamp has been used for more than 900 hours (NORMAL MODE)

No.51931

3Remove the fuse from the fuse holder you just removed.

4Install the new fuse (not supplied) into the fuse holder.

5Reinstall the fuse holder into the

projector.

To reinstall the fuse holder, use a Flat-end screwdriver.

Fuse holder

Flat-end screwdriver

Fuse (T6.3A H 250 V)

Fuse holder

Fuse (T6.3A H 250 V)

DEUTSHENGLISH

Accumulated used hours of the light-source lamp

When the lamp use time reaches 900 hours:

900 hours

The LAMP indicator lights on the projector.

 

 

 

When

starting to project after 900

hours has been exceeded:

 

 

“Lamp replacement” appears on the screen.

 

 

* The message will disappear when any button is pressed.

 

 

When

the lamp use time exceeds 1000

hours:

 

 

 

The LAMP indicator blinks on the projector.

 

“Lamp replacement” appears on the screen and the word “Warning”

1000 hours

blinks.

*To cancel this message, press the EXIT button. However, the same message will appear every hour.

*If the projector is put in stand-by mode or turned off after the lamp has been used for more than 1000 hours (but less than 2010 hours), it can

not be turned back on again unless the light-source lamp is replaced with a new one.

Replace with a new lamp (lamp unit) and reset the lamp time. (Refer to page 62.)

 

When the lamp use time reaches 1010 hours:

 

The projector is forcibly turned off.

1010 hours

The LAMP and OPERATE indicators blinks on the projector.

 

* The projector can not be turned on unless the lamp (lamp unit) is

 

replaced with a new one and the lamp time is reset. (Refer to

Lamp replacement

EXIT

Warning

Lamp replacement

EXIT

Fuse holder

57

ESPAÑOLITALIANO FRANÇAIS

page 62.)

Note

• If the projector is not put in stand-by mode or turned off, it can be used until 2010 hours is reached.

58

Image 70
Contents DLA-G150CLU About burning-in of the D-ILA device About the installation placeDo not allow any unqualified person to install the unit Can ResultContents Controls and Features Bottom Surface Control Panel on the ProjectorConnector Panel Remote Control Unit Installing Batteries Installing the ProjectorPrecautions for Installation Adjusting the vertical angle of the projector Adjusting the Inclination of the ProjectorInstalling the Projector against the Screen Leveling the projectorSetting the Amount of Lens Shifting Projection Distance and Screen SizeWhen installing adjusting/setting the unit Effective Range and Distance of the Remote Control UnitSetting the Position Selecting Screw for Ceiling Mounting Using as a wireless remote control unitVideo signals Connecting to Various DevicesSignals that Can Be Input to the Projector Allowable input signalsConnecting to Video Devices Connecting to Hi-Vision Devices/DVD PlayersTo Control Connecting to Other DevicesConnecting to Devices which Control the Projector Game device, etc Desktop typeConnecting to DVI Connecting to Computer DevicesHow to attach the ferrite core Removing the Lens Cap Lamp control settingsBasic Operations To prevent fire and electric shock, observe the followingTurning off the Power Turning on the Power Turn on the Main Power switchRemote control unit Projector’s buttonsSetting the Screen Aspect Ratio Remote control unit Turning off Image HideRemoving the Trapezoidal Distortion of the Image Zooming a Part of the Image Remote control unit Quick Alignment FunctionDisplaying a Still Picture Freeze Quick Reference Guide for No signal Menu Mode Menu Transition Diagram in No signal Menu ModeMenu Transition Diagram in Video Menu Mode Submenus in Video Menu ModeQuick Reference Guide Menu Transition Diagram in PC Menu ModeFor Video Menu Mode Factory set valueRemote control unit Projector Press the cursor Button 2 or 3 to set Or adjust the valueQuick Reference Guide for PC Menu Mode Basic Menu OperationPC menu mode Changing the Color System Video Menu Mode OnlyVideo menu mode ProjectorChanging the Language Display Adjusting Tracking/PhaseAdjust the Screen aspect ratio Or Hdtv with the cursor button 5 or ∞Select the item to be adjusted with the cursor button5 or ∞ Set up for Watching Image Software Video Menu Mode OnlyAdjusting Picture Quality Make adjustment with the cursor2 orAdjust the color temperature with Cursor button2 or Adjusting the Video Screen/Menu PositionAdjusting Color temperature Cursor button Or ∞Select Gamma or Aspect ratio with the cursor button5 or ∞ Changing the Image Gamma/Aspect Ratio Video Menu Mode OnlyChanging the Image Size Resize Function PC Menu Mode Only Select Resize with the cursor button 5 or ∞Or∞, and press the Enter button Setting and Adjusting Other Functions OptionsAdjustment item Button Or∞, and pressSelect Information with the cursor button5 or ∞ Replacing the FuseGetting Information Projector and the wall outletReplacing the Light-Source Lamp Light-source lamp and lamp use timeInside and fasten the screws Reset the lamp use timeInsert the new light-source lamp fully Loosen the screws, raise the handleCleaning and Replacing the Filter Cover Maintenance TroubleshootingWhen warning indication is shown by the blinking indicators Lamp Temp Indication IndicatorAction to be taken for warning indication OperateMessage is cleared by To cancel this message, pressPower Control Mode LPC Pressing any buttonSpecifications GL-M2915SGEnglish Deutsh Français Italiano Español Outside dimensions Pin assignment Specifications for terminalsControl command table Communication SpecificationsCommand Format RS-232C external controlAppendix ForDLA-G150CLEINSTRUCTIONS Fire Hazard To the following power supply voltage. Use onlyPower cord designated by our dealer to ensure Safety EMCReplacing 15the United Kingdom onlyVarious Devices Ferrite core ⋅ Conversion adapter for Mac for Macintosh Front Side / Top Surface / Right SideApprox m BNC-RCA Conversion plug DeutshRear adjustable foot for leveling the projector Stand by Indicator Control Panel ProjectorButton to obtain a still picture Button does not workPC buttons Gebruike batterijenInstalling the Projector English GL-M2930SZGRemote control unit Response to color systems systems 640 350 37.86 To Video Video cable accessoryHor Pixels Ver Lines KHz PC system PC98 640 400 24.83 56.42Game device, etc Hi-Vision devices BNC-RCA conversion plug accessory To VideoTo Y To PB/B-Y VHS VCRConnector Connection cable supplied To RS-232C connector To Remote terminal To monitorCable Supplied Ferrite core Basic Operations Pressed PC1 ↔ PC2 ↔ DVI Side of the unit is projectedComp The image from the Comp Y, R Image will be displayed in fullNo.51931 Quick Alignment Function Quick AlignMain menu in No signal Menu Mode Quick Reference Guide For Video Menu Mode Options → Refer to Phase Flickering or dim picture image can be adjusted toInformation → Refer to Restored Menu returns to the previous menuAuto Adjusting Tracking/Phase Image adj. submenu appears on the screen Adjust the color temperature with Cursor button 2 orOr ∞, and press the Enter button. Then, the All Video submenu Video submenu Set up 1 submenu Españolitaliano Françaisdeutshenglish Image enlarged to the full size 1365 ⋅Press the Menu button to exit the menu mode Exceeds 2000 hoursReplacing the Fuse Cover by loosening screws Stand by indicator Projector’s button Turn on the Main Power switch to goScrew Lamp-replacement opening cover Hide button With Blocked?When warning indication is shown by the blinking indicators Message Cause Corrective action Electrical system SpecificationsOptical mechanism system Input terminalsGeneral FrontUnit mm 21h Control command to the projector Designates the terminal of the data DhFunction Command Asking Operation Mode parametersFor lens unit GL-M2910G Español 2002 Victor Company of JAPAN, Limited

DLA-G150CLU, DLA-G150CLE specifications

The JVC DLA-G150CLU and DLA-G150CLE projectors represent the pinnacle of home cinema and professional presentations, offering exceptional picture quality and advanced technological features. Both models are designed to deliver an immersive viewing experience, leveraging JVC’s years of expertise in projection technology.

These projectors incorporate JVC’s renowned D-ILA (Direct-drive Image Light Amplification) technology. This innovative system utilizes liquid crystal on silicon to achieve stunning color accuracy and contrast. The DLA-G150CLU and DLA-G150CLE boast an impressive native resolution of 1920x1080, allowing for incredibly detailed images that are perfect for both high-definition films and intricate graphics. The contrast ratio of these projectors reaches up to 20,000:1, making dark scenes richer and more dynamic while ensuring bright areas remain vivid without washing out.

Color reproduction is another strong point of the JVC DLA-G150 series, featuring an expansive color gamut that adheres closely to industry standards. The projectors utilize a dual-lamp system, allowing for increased brightness levels of up to 2500 lumens, which ensures clear visibility even in well-lit environments. This feature is particularly beneficial for presentations in conference rooms or larger venues where ambient light may compromise image quality.

Both the DLA-G150CLU and DLA-G150CLE support a wide range of connectivity options, including HDMI and RS-232 ports, making them versatile for various setups. This connectivity is further enhanced by an intuitive on-screen menu system, allowing users to easily adjust settings and calibrate the projector for optimal performance.

For those who value flexibility, the JVC DLA-G150 projectors come with lens shift capabilities, enabling vertical and horizontal adjustments. This feature allows users to position the projector without compromising image quality, catering to different installation environments.

In conclusion, the JVC DLA-G150CLU and DLA-G150CLE projectors embody the perfect blend of advanced technology and user-friendly features. Whether used for home entertainment or professional applications, they offer unparalleled performance, making them an excellent choice for anyone seeking high-quality projection solutions.