JVC DLA-G150CLE, DLA-G150CLU manual Main menu in No signal Menu Mode

1-60

Basic Operations

■ Remote control unit Displaying a Still Picture (FREEZE)

Menu Operations

You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the following menu transition diagrams, you can see the overall menus and basic button operation in menu mode. Note that there are three menu modes, No signal menu mode, video menu mode and PC menu mode. When the MENU button is pressed,

DLA-G150CLU DLA-G150CLE

QUICK

ALIGN.

	HIDE
W
SCREEN	FREEZE
S
PC1	PC2

OPERATE

COMP VIDEO

DVI Y/C

FREEZE button

While projecting an image, a still picture is obtained at any time by using the FREEZE button on the remote control.

When you press the FREEZE button:

“FREEZE” appears on the screen for a few seconds and

then the still picture is shown on the screen. Refer to the FREEZE message shown on the left of this page.

* To forcibly clear “FREEZE”, press the EXIT button.

the projector enters one of these modes by judging the input signal being received.

■Menu Transition Diagram in No signal Menu Mode

This is displayed if there is no signal from the selected input terminal.

Main menu in No signal Menu Mode Submenus in No signal Menu Mode

DIGITAL ZOOM T/W button

PRESET button

EXIT button

	T
KEYSTONE	DIGITAL
	ZOOM
	W
	PRESET
	EXIT

RM-M160 REMOTE CONTROL UNIT

T

ZOOM FOCUS

W

MENU

ENTER

Cursor buttons 5/∞ / 2/3

When you press the FREEZE button again.

The original image resumes.

Remote control unit FREEZE

Notes

Press 5/∞ to select an item.

Menu

Set up Sync level

Sync timing

Options

3 or ENTER

Press 5/∞ to select an item. Press 2/3 to set the value.

Set up

Sync level Low Std High

Sync timing

• During freezing, the picture sent from the signal source is

lost.

• If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”,

Language Information

EXIT

FREEZE message

FREEZE

FREEZE inhibit message

“KEYSTONE”) are pressed while displaying a still picture,

“FREEZE” is displayed on the screen.

• This function will not work with some signal sources

(UXGA, etc). In this case, the FREEZE inhibit message

appears for a few seconds, as shown on the left. To forcibly clear this message, press the EXIT button.

Zooming a Part of the Image

(DIGITAL ZOOM T/W)

A part of the image being projected can be digitally magnified up to four times. When the DIGITAL ZOOM T or W button is

pressed, “Digital zoom” appears on the screen together with the level bar and magnifying power ( ⋅ 1.0, ⋅ 1.2, ⋅ 1.4, ⋅ 1.6, ⋅ 2.0,

∞

5

Menu

Set up

Options

Language

Information

5 ∞

English

Deutsch

Español

Italiano

Français

5 ∞

Press 5/∞ to select an item.

Language

3or

ENTER	English
	Deutsch

	Español
EXIT
	Italiano
	Français

No.51931

FREEZE

DIGITAL ZOOM inhibit message

D.ZOOM

⋅ 2.5, ⋅ 3.2, ⋅ 4.0). When “15 sec.” is displayed in the menu,

“Digital zoom” will appear in approximately 15 seconds.

Digital zoom 1.2

•To zoom up or zoom down, press the DIGITAL ZOOM T or W button on the remote control.

Remote control unit

T

DIGITAL

ZOOM

W

Moving the zoomed image:

While “Digital zoom” appears on the screen, you can move

the zoomed image with the cursor ( 5/∞/2/3) button on the remote control.

5: Upper part of the image will be displayed.

∞: Lower part of the image will be displayed.

2: Left side part of the image will be displayed.

3: Right side part of the image will be displayed.

Notes

•This function will not work with some signal sources (UXGA, etc). In this case, the DIGITAL ZOOM inhibit

message appears for a few seconds, as shown on the left. To forcibly clear this message, press the EXIT button.

•The quality of the zoomed image reduces in comparison with the original one.

•To return to the original size ( ⋅ 1.0) and original position, press the PRESET button while “Digital zoom” is displayed

on the screen.

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

Menu
	Input	PC1
Set up	Switcher	CH.0
Options
Language
	Lamp time	123 h
Information

■Quick Reference Guide for No signal Menu Mode

Main Menu in No signal Menu Mode
	Set up
		Sync level:	Low. Std*. High.
		Sync timing:	3-5
	Options
		Flip H:	OFF* / ON (Select for upside-down hanging on the ceiling.)
		Flip V:	OFF* / ON (Select for upside-down hanging on the ceiling.)
		RS-232C [bps]:	Selectable baud rate (transmission speed). 9600 / 19200*
		Sleep time [min]: Selectable sleep times. If no-signal condition continues for the period of selected time
			(Unit: Minutes), the projector enters the stand-by mode. 15 / 30 / 60 / OFF*
	Language		Language for on-screen display.
		Japanese / English* / German / Spanish / Italian / French
	Information
		Input:	Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP,
			PC1, PC2 or DVI)
		Switcher:	Has no meaning. This display currently has no meaning. (“CH.0” is usually displayed to
			indicate that it is not being used.)
		Lamp time:	Accumulated used hours of the light-source lamp.

37

38