JVC DLA-G150CLE, DLA-G150CLU manual When warning indication is shown by the blinking indicators

1-74

No.51931

						Troubleshooting
Symptom			Probable cause			Corrective action		Page
A part of image is		•	Was the DIGITAL ZOOM T button on			• Press the PRESET button to restore the		12, 37
magnified.			the remote control pressed?			original video screen.
Color is poor	or	•	Is picture quality (color density, etc.)			• Adjust picture quality on the menu.		49
unstable.			adjusted correctly?
		•	Is the correct color system selected?	•		Set the color system to AUTO or to the		45
						correct dedicated color system.
		•	Are signals (scanning frequency, etc.)			• Check if the signal is appropriate (scanning		22
			of the connected devices appropriate?			frequency, etc.), and input the appropriate
						signal.
The upper part of the		•	While computer system signal is input,			• Input separate sync signals for vertical sync		11, 28
video image	bows or		isn’t a sync signal for composite sync			(V) and horizontal sync (H) signals.
distorts.			(Cs) or G on sync being input?
		•	Isn’t signal with much jitter or skew			• Input signals with little jitter or distortion.		–
			distortion being input from a video			Use a TBC or a device with a built-in TBC.
			deck?
Video image		•	Is video picture turned off by pressing			• Turn on video picture by pressing the HIDE		10, 12,
suddenly go	out.		the HIDE button?			button.		35
Remote control unit		•	Are batteries installed correctly?		• Match the polarities of batteries correctly (+			14
does not work.						to + and – to –).
		•	Are batteries exhausted?	•		Replace with new batteries.	14
		•	Is there a shielding object between the			• Remove any shielding objects.	20
			remote control unit and the remote
			sensor?
		•	Is the distance too long?		• Use the remote control unit at a nearer			20
						point.
		•	Is either side of remote cable			• Firmly insert the remote cable when using		21
			disconnected?			the remote control unit as the wired one.
* This device uses a computer. External noise may cause it to malfunction. If this happens, turn the power off, remove the
electric plug from the wall outlet. Then insert the electric plug back into the wall outlet, turn the power back on and check t								he
operation.

■When warning indication is shown by the blinking indicators:

The warning status will be notified by the combination lighting of the projector’s indicators.

For the warning contents and the action to be taken, refer to “Warning Indication” on page 66.

■Maintenance

• Stains on the cabinet

These should be wiped off with a soft cloth. If the cabinet is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wring well, then wipe clean with a dry cloth.

•Since the cabinet may deteriorate in quality, become damaged, or show paint peeled, note the following:

–Do not wipe with rough cloth.

–Do not wipe vigorously.

–Do not wipe with thinner or benzene.

–Do not apply any volatile substance such as insecticides.

–Do not allow any rubber or vinyl article to remain in contact with the cabinet for a long time.

•Stains on the lens

These should be cleaned off with commercially available lens blowers or lens cleaning paper (for cleaning glasses and cameras).

Do not use liquid cleaning agents. This could cause the surface coating to be removed. Do not rub, scratch or hit the lens as its surface is prone to damage.

65

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

Warning Indication

If something abnormal has occurred with the projector, the warning status will be indicated by the combination of lighting the

indicators on the control panel as shown in the following table. Then, the projector automatically stops projection and runs th e cooling fan for about 120 seconds.

Warning	indication		table:
No.					Indicator					Warning content
		LAMP		TEMP	STAND BY		OPERATE
1		Blink				Blink			The	light-source lamp does not light and projection
										is not made.
2		Blink						Blink	The	light-source lamp has suddenly gone off during
										projecting an image.
3		Blink		Blink					Circuit operation is abnormal.
4						Blink		Blink	The filter is displaced.
5				Blink					The internal temperature is too high. (Sensor 1)
6				Blink		Blink			The internal temperature is too high. (Sensor 2)
7		Blink		Blink		Blink	Blink		The cooling fan has stopped (locked).

* For individual indicator lighting, refer to page 58.

■Action to be taken for warning indication

Stopping the projector:

After the cooling fan has stopped, take the following action.

No. 1 : Check that the cover for replacing the light-source lamp and the front panel are securely attached, and then, press the OPERATE button for one second or more to turn on the projector for retrying.

No. 2 : Check that the cover for replacing the light-source lamp and the front panel are securely attached, and then, press the OPERATE button for one second or more to turn on the projector for retrying.

No. 3 : Press the OPERATE button for one second or more to turn on the projector for retrying.

Nos. 4-7 : Follow the next steps.

1.Turn off the MAIN POWER switch and unplug the power cord from the wall outlet.

2.Take an action according to the number.

No. 4 : Set the filter in place.Then, leave the projector until it cools down.

No. 5 : Check that nothing is blocking the air inlet nor outlet, and wait until the inside cools down.

No. 6 : Check that nothing is blocking the air inlet nor outlet, and wait until the inside cools down.

No. 7 : Leave the projector until it cools down.

3.Plug in the power cord again, turn on the MAIN POWER switch, and press the OPERATE button for one second or more to turn on the projector for retrying.

Retrying operation:

Plug in the power cord again and operate the projector.

If the same warning indication is observed again, after the cooling fan has stopped, turn off the MAIN POWER switch, unplug the power cord, and call your dealer for repair.

66

DLA-G150CLU DLA-G150CLE