Analog Devices ADSP-2181, ADSP-2183 manual Reset GND, Pm, Dm, Bm, Iom, & Cm

Page 11

ADSP-2181/ADSP-2183

These ADSP-2181/ADSP-2183 pins must be connected only to the EZ-ICE connector in the target system. These pins have no function except during emulation, and do not require pull-up or pull-down resistors. The traces for these signals between the ADSP-2181/ADSP-2183 and the connector must be kept as short as possible, no longer that 3 inches.

The following pins are also used by the EZ-ICE:

BR

BG

RESET

GND

The EZ-ICE uses the EE (emulator enable) signal to take con- trol of the ADSP-2181/ADSP-2183 in the target system. This causes the processor to use its ERESET, EBR, and EBG pins instead of the RESET, BR, and BG pins. The BG output is three-stated. These signals do not need to be jumper-isolated in your system.

The EZ-ICE connects to your target system via a ribbon cable and a 14-pin female plug. The female plug is plugged onto the 14-pin connector (a pin strip header) on the target board.

Target Board Connector for EZ-ICE Probe

The EZ-ICE connector (a standard pin strip header) is shown in Figure 7. You must add this connector to your target board design if you intend to use the EZ-ICE. Be sure to allow enough room in your system to fit the EZ-ICE probe onto the 14-pin connector.

Target Memory Interface

For your target system to be compatible with the EZ-ICE emu- lator, it must comply with the memory interface guidelines listed below.

PM, DM, BM, IOM, & CM

Design your Program Memory (PM), Data Memory (DM), Byte Memory (BM), I/O Memory (IOM), and Composite Memory (CM) external interfaces to comply with worst case device timing requirements and switching characteristics as specified in the DSP’s data sheet. The performance of the EZ-ICE may approach published worst case specification for some memory access timing requirements and switching characteristics.

Note: If your target does not meet the worst case chip specifi- cation for memory access parameters, you may not be able to emulate your circuitry at the desired CLKIN frequency. De- pending on the severity of the specification violation, you may have trouble manufacturing your system as DSP components statistically vary in switching characteristic and timing require- ments within published limits.

Restriction: All memory strobe signals on the ADSP-2181/ ADSP-2183 (RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your target system must have 10 kΩ pull-up resistors connected when the EZ-ICE is being used. The pull-up resis- tors are necessary because there are no internal pull-ups to guarantee their state during prolonged three-state conditions resulting from typical EZ-ICE debugging sessions. These resis- tors may be removed at your option when the EZ-ICE is not being used.

GND

EBG

EBR

KEY (NO PIN)

ELOUT

EE

RESET

12

34

56

78

×

9 10

1112

1314

TOP VIEW

BG

BR

EINT

ELIN

ECLK

EMS

ERESET

Target System Interface Signals

When the EZ-ICE board is installed, the performance on some system signals change. Design your system to be compatible with the following system interface signal changes introduced by the EZ-ICE board:

•

EZ-ICE emulation introduces an 8 ns propagation delay

 

between your target circuitry and the DSP on the

RESET

 

 

signal.

•

EZ-ICE emulation introduces an 8 ns propagation delay be-

 

tween your target circuitry and the DSP on the

BR

signal.

•

EZ-ICE emulation ignores

 

and

 

when single-

RESET

BR

 

stepping.

•

EZ-ICE emulation ignores

 

and

 

when in Emula-

RESET

BR

 

tor Space (DSP halted).

Figure 7. Target Board Connector for EZ-ICE

The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca- tion—you must remove Pin 7 from the header. The pins must be 0.025 inch square and at least 0.20 inch in length. Pin spac- ing should be 0.1 × 0.1 inches. The pin strip header must have at least 0.15 inch clearance on all sides to accept the EZ-ICE probe plug. Pin strip headers are available from vendors such as 3M, McKenzie, and Samtec.

• EZ-ICE emulation ignores the state of target BR in certain

modes. As a result, the target system may take control of the

DSP’s external memory bus only if bus grant (BG) is asserted

by the EZ-ICE board’s DSP.

REV. 0

–11–

Page 10 Page 12
Image 11
Page 10 Page 12
Contents General Description Functional Block DiagramArchitecture Overview ADSP-2181/ADSP-2183ADSP-2181/ADSP-2183 Integration PIN Descriptions Pin Input Names Pins Output FunctionLowest Priority Interrupt VectorSource of Interrupt Address Hex Highest PriorityADSP-2181 ADSP-2183 System InterfaceMemory A13 A120 PmovlayMemory Space Word Size Alignment Address Range Wait State RegisterInternal Idma Port Booting Booting MethodDesigning AN EZ-ICE-COMPATIBLE System Syntax IOaddr = dreg dreg = IOaddrBiased Rounding Instruction SET DescriptionPM, DM, BM, IOM, & CM Reset GNDGrades Parameter Test Conditions Min Max Unit Grade Parameter Min Max UnitESD Sensitivity Memory Timing SpecificationsFrequency Dependency for Timing Specifications Absolute Maximum Ratings41C/W 10C/W 31C/W Package50C/W 2C/W 48C/W Test Conditions Capacitive LoadingADSP-2183-SPECIFICATIONS ADSP-2183 Timing Parameters Tqfp Delay Valid Output 28.8 MHz Parameter Min Max Clock Signals and Reset Parameter Min Max Unit Clock Signals and ResetControl Signals Flag Output Hold after Clkout Low5 5tCK FI, or PFx Setup before Clkout Low1, 2, 3 25tCK + IRQxFlag Output Delay from Clkout Low5 25tCK + Parameter Min Max Unit Interrupts and FlagParameter Min Max Unit Bus Request/Grant 28.8 MHz Parameter Min Max Unit Memory Read Parameter Min Max Unit Memory ReadParameter Min Max Unit Memory Write Parameter Min Max Unit Serial Ports Parameter Min Max Unit Idma Address Latch Parameter Min Max Idma Write, Short Write Cycle Parameter Min Max Unit Idma Write, Short Write Cycle28.8 MHz Parameter Min Max Unit Idma Write, Long Write Cycle 28.8 MHz Parameter Min Max Unit Idma Read, Long Read Cycle Parameter Min Max Unit Idma Read, Long Read Cycle28.8 MHz Parameter Min Max Unit Idma Read, Short Read Cycle Parameter Min Max Unit Idma Read, Short Read CycleLead Tqfp Package Pinout Number Name PinOutline Dimensions Millimeters Inches Symbol MIN TYP MAXLead Pqfp Package Pinout PF0 160 Ordering Guide Page Page C2144-16-6/96
Top Page Image Contents