VXI VM4016 user manual Description, Front Panel Layout

Page 12

ACC/ FAIL ERR

J200

ACC/ FAIL ERR

J201

ACC/ FAIL ERR

J202

bus

VXI Technology, Inc.

Regardless of whether the VM4016 is configured with other VM4016 modules or with other VMIPmodules, each group of 16 channels is treated as an independent instrument in the VXIbus chassis and, as such, each group has its own FAIL and ACCESS light.

The FAIL LED is a Power/Fault indicator. When normal power up conditions exist, the FAIL LED will illuminate green. When a power on fault condition occurs, the FAIL LED will illuminate red. The ACC/ERR LED indicates communication status. When a successful Access occurs, the LED will blink green during data transfer and command/query operations. In the event of an unrecognized command, or other data related error, the ACC/ERR LED will illuminate red. If there is no command/query activity, and no errors, the ACC/ERR LED will be extinguished. The normal state of the LEDs on a properly functioning idle instrument is for the FAIL LED to be green, and the ACC/ERR LED to be off.

DESCRIPTION

The VM4016 is a high-performance Analog Comparator module with 16 input channels per VMIP daughter module. Each input channel consists of a differential amplifier with a gain of 1 or 0.1 giving an input range of ±10 volts or ±100 volts. Each input is compared against a reference voltage derived from an independent 8-bit DAC.

Each input signal is digitally debounced for a programmed time ranging from approximately 10 ∝s to 0.5 seconds. This prevents input signal noise from causing undesired interrupts. After debounce, the signal may be programmatically inverted to select the input transition edge of interest (rising or falling edge) and masked to prevent unused channels from causing interrupts.

All of the masked inputs are OR’d together to produce a single interrupt signal. This interrupt signal is used to generate a VXIbus interrupt as well as the front panel interrupt outputs. All active input is recorded as a 1. Once the VXIbus interrupt is serviced by the slot 0 controller, the First Latched Register will be cleared.

The state of each channel’s debounced input and the inverted and masked status may be read directly in the user defined area of the VXIbus registers as can the First Latched register. This information may also be retrieved using the message-based word serial interface.

The block diagram of Figure 1-3shows the overall functionality of the VM4016 Analog Comparator instrument.

FIGURE 1-2: FRONT PANEL LAYOUT

12

VM4016 Preparation for Use

Image 12
Contents VM4016 Page Table of Contents VXI Technology, Inc Warranty Limitation of WarrantyCertification Restricted Rights LegendC L a R a T I O N O F C O N F O R M I T Y EMCGeneral Safety Instructions Terms and SymbolsThis product. Product should be inspected or serviced Support Resources VXI Technology, Inc VM4016 Preface Introduction IntroductionDescription Front Panel LayoutVM4016 Block Diagram VM4016 General Specifications IRQ OutputInstallation Calculating System Power and Cooling RequirementsPreparation for USE Setting the Chassis Backplane Jumpers Setting the Logical AddressFront Panel Interface Wiring Signal PIN Number Analog Comparator PIN Outs1631 Examples of Scpi Commands FETCHCONDITIONED? ProgrammingFETCHLATCHED? FETCHRAW? Inhousepseudo Inhouseregint InhouseregintInhouseregenable Inhouseclearlatch Inputdebounce ExamplesInputmask INPMASK?INPutMASKINTerrupt boolean Where boolean is 0 OFF 1 on InputmaskinterruptInputoffset INPOFFS?Inputpolarity INPutPOLarity NORM,@35Inputrange Outputpolarityexternalinterrupt Outputpolarityexternallatched Application Examples ExampleCommands Description Single Channel OperationControl Page Bracketing a Voltage Sets the external interrupt output to be active highBracketing AN Input Voltage Page Register Access Examples Register MAPFor example Pseudo Register Access VXIPLUG&PLAY Driver Examples VM4016 Programming VXI Technology, Inc Command Dictionary Alphabetical Command ListingIeee 488.2 Common Commands Instrument Specific Scpi Commands NormalScpi Required Commands Command Dictionary Query ParametersCommon Scpi Commands CLSESE Response DescriptionESR? IDN? OPC Query Parameters Query Response DescriptionRST SRE STB? TRG TST? WAI OPCInstrument Specific Scpi Commands FETChCONDitioned?FETChLATChed? FETChRAW? Inhouseclearlatch Inhousepseudo Inhouseregint Inhouseregenable INPutDEBounce INPutMASK INPutMASKINTerrupt INPutOFFSet INPutPOLarity INPutRANGe OUTPutPOLarityEXTernalINTerrupt OUTPutPOLarityEXTernalLATChed Required Scpi Commands STATusOPERationCONDition?STATusOPERationENABle STATusOPERationEVENt? STATusPRESet STATusQUEStionableCONDition? STATusQUEStionableENABle STATusQUEStionableEVENt SYSTemERRor? SYSTemVERSion? Theory of Operation Input Range Control Relay Signal Comparison Interrupt Generation Interrupt Generation Index OUTPutPOLarityEXTernalLATChed